plumber

Thanks I'll try it.

When I'm riding and coming to a stop I push in the clutch my rpm stays up until I let out on the clutch a little then my rpm goes down and everything is ok is my throttle cable sticking ?

I have a new rear and front diff for a Renegade I know Lenny and Rocmoc use these on there trooper because they are lower geared for the bigger tires. I'm asking 900.00 for both plus shipping Lenny can tell you more about it than me.

everything gone

That's about the same miles I have 1500 miles I found out about joyner off the internet. Kinarfi , I think has about the most miles

Has anybody seen these http://www.amazon.com/EVO-Tech-Performance-REMOTE-Joyner-Trooper/dp/B0078BXSGW/ref=sr_1_1?ie=UTF8&qid=1366507356&sr=8-1&keywords=joyner+trooper . http://www.amazon.com/Magnum-Remusshield-Finger-Immobilizer-Trooper/dp/B00BOVXC4K/ref=sr_1_2?ie=UTF8&qid=1366507356&sr=8-2&keywords=joyner+trooper . http://www.amazon.com/Dyno-Boost-Adjustable-Controller-Performance-Trooper/dp/B004ZPPH0O/ref=sr_1_20?ie=UTF8&qid=1366507464&sr=8-20&keywords=joyner+trooper

WOW,I,m amazed one more time.

http://electronicjetkit.com/UTV/viewproduct.asp?partnumber=9340001

Do anybody have one of these or used one of these. http://www.nomartirechanger.com/

Long time no see hope you and your family are doing great! Has anybody rolled there Trooper ? If you watch the video it is leaning a lot before going over

Dave this might help! http://www.utvboard.com/topic/392-parts-pieces-and-information-for-our-troopers-joyners/ look a little down on the list.

That would be pocket change

rocmoc, I found you a jeep petty neat Curb Weight (estimated): 3,850 lb (1,746 kg) Length: 151.8 inches (3,856 mm) Wheelbase: 108.1 inches (2,746 mm) Front Overhang: 25.0 inches (635 mm) Rear Overhang: 18.7 inches (475 mm) Width: 80.0 inches (2,033 mm) Height: 68.2 inches (1,732 mm) Track, Frt/Rr: 67.5/67.5 inches (1,715/1,715 mm) Engine: Two 5.7-liter, 8-cylinder HEMI engines Power: 670 hp (500 kW) (2 x 335 hp) Torque: 740 lbf·ft (1000 N·m) (2 x 370 lbf-ft) Transfer Case: Custom multi-mode with 1:1, 2:1 and 4:1 ratios Transmission: 5-speed automatic Front and Rear Suspension: Long-travel, short/long arm independent Ground Clearance: 14.3 inches (363 mm) Break-Over Angle: 31.5 degrees Approach/Depart Angle: 64.0/86.7 degrees Tire Size: 305/70R20 (all four) Wheel Size: 20x10 inches (51x25 cm) 0-60 mph (97 km/h): 4.9 seconds

#2 S11-3605010TA R2/R4 800 372ECU 1 561.35 #2 S11-3605010JA Trooper ECU 1 709.10 I would say yes they are different the last two number are different and the price are different

#2 S11-3605010TA R2/R4 800 372ECU 1 561.35 #2 S11-3605010JA Trooper ECU 1 709.10 . If you look at the numbers the last two number are different so I would say yes they are different

Hey Dave it's so hard for me to plan something I'll let you know when it gets closer. I need to go it's been awhile since I been riding.Is it a 60" wide restriction my trooper is 64" wide

http://www.harlancountytrails.com/blackmountain.php Very adventurous

WOW I have 1500 miles on mine

I wish you the best on getting all you can get for it. But I think 3500.00 I have and 08 Trooper with a lot of things done to it and if I would sale it right now 5000.00 And then there on the east coast well here in Ky they are hard to sale.

I have but it was only about 6" it done fine I also have a 6' snow plow for mine

I bought one of these I have had it for about 4 days now and this thing is BAD ASS I cut 3/4" steel tonight with it no problem. If you want a plasma cutter at a good price this is it.

If anybody needs a plasma cutter here is one for a good price http://www.amazon.com/Everlast-SuperCut-Inverter-plasma-Cutting/dp/B004K1MYNQ/ref=sr_1_5?s=power-hand-tools&ie=UTF8&qid=1351906392&sr=1-5

Look's great kinarfi glad you could do something with them.

No mine is up high you can look in the gallery and see it or go to ebay motors type in joyner trooper and the blue one with the big winch up front is mine

Yes the winch cradle goes into the back receiver. I also had the winch behind the plastic piece too I took out the old winch and made a 1/2" steel plate that was the same shape as of the steel plate that the winch bolts down to and welded a 2" receiver on it and bolted it down. I ran #4 welding cables to the quick disconnect coupling I used the ANDERSON CONNECTOR 600V KIT SB 175 SERIES 175 AMP 4 GA They work great