Search the Community
Showing results for tags 'renegade'.
Found 22 results
-
Recently inherited 08 joyner renegade r4 800.. seems to be sound mechanically but I cannot find bal joints. Any pone help with other replacement part number please.
-
Hello, I found an 08 Renegade for sale and looking to purchase it. I haven’t heard too much about these machines and any insight would be much appreciated. Are they good machines?
-
Looking for right front cv axle .Does anyone have one or parts to one or know of a place i can order one.I think Joyner manuefacture closed down.I have the inner axlecv joint i need the outer that goes threw the wheel.
-
I'm in need of a brake master cylinder for my ride. Appears to be leaking between the reservoir and the cylinder (picture). Is there a seal that I can replace inexpensively without buy a whole master cylinder assembly? Can't tell if the master cylinder is the same as used on the Trooper because I don't have a Trooper parts manual. I don't know if the master cylinder is different when they went to the 1100cc engine. Has anyone had experience with master cylinder make for the Kinrod Joyner line of rides (I believe it's a German company)? They are available on Amazon but the configuration isn't the same as OEM.
-
where do you access the cable adjustment ? -
Plastic actuator is shot. Any direction for a part, or possible fix?
-
Very new to any forum. Haha We have an 09 R2 joyner renegade 800cc. We are unable to start it. It has been sitting for a few seasons. It has spark(new plugs), it get gas, fuel pump works(new), fan comes on on initial key turn, sounds like system doing its check. It's turning over but nothing. Clean fuel, gas tank cleaned, fuel going through all the lines. Relays and fuses checked and pulled and reseated. New battery even. Thanks yall.
-
Hey all, Looking to possibly purchase a 2008 Renegade 4 seater, 11000 miles. asking $5,000 I know nothing about these machines, they seem pretty decent. Hard to find any info on them even on youtube. Anyone had any advice, or things to look at before buying? Thanks in advance!
-
View File Joyner Renegade R2/R4 Owner, Repair, Parts Manual Pre-2014 Renegade with the 800cc engine. Much of this may apply to the R4 also. Note to moderator: Please add "Joyner" to the list of UTVs. Submitter Dan B Submitted 02/14/2021 Category Joyner
-
Hey guys! My throttle cable broke in its housing. Can anyone tell me what aftermarket cable would work for a 1100 renegade Joyner? TIA
-
The brake pads on my Renegade seem to be quite thin, less than 1800 miles. Does anyone know what the thickness of new brake pad friction material is. It will give me an idea as to how much brake pad life I might have left. A supplier or suitable substitues would also be helpful in case I need to get new ones. Thanks in advance.
-
Have a new r4 approx 800 miles just noticed the tach wont sweep with ignition on but the speedo does, also will start with out the clutch engaged. my 2012 r4 tach and speedo both sweep and it wont start unless the clutch is engaged , any ideas why?. Any help would be greatly appreciated. Thanks Matt
-
I have a 2016 R4 and I was about to load it on my trailer and the steering just broke I think. My front wheels are both pointing outwards. Does this mean front differential broke? I jacked it up and got them both pointing in the right direction. When up in the air they work together. But as soon as I put back on the ground and move it a few feet they separate again.
-
Couldn't find in parts and pieces any aftermarket front lower ball joints for an 09 Renegade. Thanks in advance if you can help.
-
New to this forum i have been looking for a rim for our rig for several days called joyner and a dealer in mississippi but no luck been told they don't make em was just wondering if anyone pulled any off and want to sell did find some in cali but won't ship lol thanks in advance
-
Tried to remove my skid plate to access the engine oil drain plug. The plug isn't near an access hole but located between two holes. Can't get a wrench in to remove the plug. Short of drilling a new access hole (which I'm seriously considering), has any one been able to remove the skid plate? Seems to be a nut on the other end of the screw and there's no way I can access that nut. They must have bolted the skid plate on before putting the engine into the frame. Thanks in advance.
-
-
I'm new to 4WD. I have a 2014 Renegade T2, 1100cc engine, 1700 mi. I'm having difficulty selecting 4WD. I don't want to do anything that might cause damage. The only info I can find is to bring the UTV to a complete stop before selecting 4WD. When I do that, the handle doesn't seem to engage 4WD; it doesn't stay in the down position. Do I have to release the clutch? Do I have to drive forward / backward to make it engage? I don't think I have a transmission problem (no grinding of any gears). Maybe a cable adjustment issue? Thanks in advance for your help.
-
New to the forum, of course. Just bought a used R2 with an 1100cc engine. Don't know why it took so long for Joyner to do that with the Renegade. Hope to learn a lot about my machine.?
-
Check out this amazing Black Friday Sale! Up to $3,000 off MSRP, this week only-- Brand New 2016 Joyner 1100cc Sand Viper $8,000 (MSRP $11,000), 2016 Joyner 1100cc Renegade R2 only $9,000 (MSRP. $12,000), 2016 Joyner 1100cc Renegade R4 is $10,000 (MSRP $12,500). Don't miss out on this low low price, mention code BFS16 when you come in to get this awesome deal or call us for more info! 480-882-9612 https://www.facebook.com/JoynerUSA/ -
PBO Auto Sales 3842 E Roeser Rd Phoenix, AZ 85040 FULL Service Dealer with a Master Mechanic NEW Units in Warehouse ready for delivery ( All Models) Call for details: 602-828-1885 or visit my website www.pboautosales.com Largest Dealer in the country and located across the street from Joyner USA
