Quantcast
Jump to content


Recommended Posts

Posted

I read with envy about the fun at the 1st Annual Trooper Jamboree.

This Summer I'll be taking part in the Annual ATV Outlaw Jamboree in Eagar Arizona. UTVs are welcome along with the ATVs. Take a look at the official website to see the kind of country you'll be riding in.

http://www.azatvoutlawtrail.com/

If you are into beautiful high mountains, tall trees, and history of the Old West, you need to make it a point to attend this Jamboree. See where famous outlaws hid out, where John Wayne had his ranch, and other interesting sites.

This annual event has something for almost everyone as a look at the official website will show. Entries are limited to 400 riders so get your entry in while you can.

Last year was a great success and this year should be even better.

Gumball

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Nutcase
      I have a Joyner Trooper 1100 4 place that has been sitting for a number of years. I have everything taken care of but i can't get the fuel through the injectors. Fuel pump puts full pressure on them but they don't turn on or spray fuel. Any ideas?
    • By aefron88
      This post will explain how to hook up your PC to the ECU of a Hisun/Coleman/Etc UTV to be able to read error codes & engine parameters for troubleshooting purposes.
      This is applicable to all small engines using the Delphi MT-05 ECU. This should cover all fuel injected Hisun models, as well as various other Chinese FI engines, as the Delphi MT-05 ECU seems to be the favored ECU solution.
      Even though we get actual engine error codes to display on the dash, sometimes we have “pending codes” (not yet confirmed by the ECU) or other intermittent issues that are hard to diagnose, for example a poorly connected sensor that may give intermittent false readings, or a sensor that’s putting out bad date, but not bad enough for the ECU to realize.
      The setup requires 2 cables, which are available for around $25 combined, a PC with a USB port, and some charityware software called “HUD ECU Hacker”. This gives the same functionality as the $300 dealer code scanner for a fraction of the price.
      In searching I found info about HUD ECU Hacker, but I have yet to see info anywhere about how to hook it up to a Hisun, so I took the leap and bought some cables, and made it work. I will show a step by step of how to do so in post two.
      I will be breaking this down into 2 posts:
      Delphi ECU Info & Overview (This post) System setup & use Delphi ECU Info (Skip ahead to the next post if your eyes glaze over technical details)
      The Delphi MT-05 ECU was developed to allow small engines to use fuel injection. A fuel injection system requires feedback from various sensors to operate efficiently. This feedback allows the adjustment of ignition timing, fuel injection volume, etc to efficiently and cleanly produce the most power possible from a given engine.
      The MT-05 ECU has a number of sensors that are required for proper functioning including; Coolant temp, crankshaft position, intake temp, intake pressure, exhaust O2, throttle position, as well as some other optional sensors that are used on more complex vehicles.
      From the sensors the ECU adjusts: Fuel injector timing/pulse, Idle air control valve, and ignition coil

      The Delphi MT-05 puts out diagnostic data, however it is not ODB2 like a modern car, where is where it gets tricky reading it. There are three options, there is an old 16 bit piece of software Delphi has that is not able to run on a modern computer, there is the motorscanner tool for dealers ($300), or there is freeware HUD ECU Hacker with the proper cables.
    • By GWS
      I am looking for the part numbers for the primary and safety air filters that will fit a 2020 Tracker 800SX
    • By Dale Halifax
      I'm a newbie.  While I'm testing out my new to me 2021 Massimo T-Boss 410 winch, I broke the Orange Ring that fits around the cable.  I can't see much of a purpose for this ring, other than to be in the way, and to break.  Is this ring really necessary?  I did find it on the Massimo winch parts diagram, but I'm thinking,  Meah?  Am I wrong?   (It's # 13 and 14 on the parts diagram, attached)
      Thanks.

    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
×
×
  • Create New...