Quantcast
Jump to content


Recommended Posts

  • Alex changed the title to Radio for Axis 500
Posted

Like a car stereo? Most people run small Bluetooth soundbars from what I've seen, although it might be hard to hear over the engine when driving.

You could find a spot for a car stereo. But you would also need to find space for speakers, which would be tough.

Posted

I started out where you are. Tried to find the best way, using old school ideas. Here's what I found. By the time you collect all the components, radio, speakers, amp, etc. The portable bluetooth speaker sounds better all the time(pun intended).

I have the W-King X10. Plenty loud with decent bass, plenty of  volume, and it'll last for hours on high. Got a cheap velcro type bar mount for it. Less than a hundred for both, problem solved, and it pops right out for carry, or you can charge small electronic devices with the oversized battery.

If that's not enough noise, then there's always a tailgating type powered speaker. I've got one of those too. When it's jamming, it's so loud, that it's uncomfortable to walk up to it to manually turn it down. And it's a cheap one. $120 bucks or so. A comparable in dash sound system would be $300 easily. And it can run down your battery if you leave it cranking out tunes while you party. The more power it puts out, the faster that'll happen. The speaker just works, I've never looked back.

20220723_083311.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By NC4wd
      Has anyone found a lift kit that fits an Axis 500? Mine is a 2021.
    • By Justine
      I've had a Hisun Vector E1 for just a bit longer than is required for me to do some maintenance. While it's well-overdue, it only drives 1.5km a few times each week on a fairly decent gravel road (to the letterbox), and it has worked really well right from the get-go.
      Looking at the manual it states that I need to use SAE80 API GL-4 Hypoid Gear Oil for the Main gear Case, and SAE80 API GL-5 Hypoid Gear Oil for the Front gear Case - unfortunately i can't find either of those online here in Australia. Plenty of options that look close, but, as someone who has never driven any vehicle before, I want to use the right thing and it's a tad confusing.
      My question: Since there are no oils that are bang on SAE80 (they all seem to cover a range) would Liqui Moly Hypoid GL4 Gear Oil 80W-90  & Motorex Hypoid GL-5 Gear Oil 80W90 - be ok to use? (Or any other suggestions of what I might be able to purchase online in Australia) And would I have to drain out any existing oil from both gear cases?
      This is a whole new world for me and  being able to find exactly what is specified in the manual hasn't made this easy!
    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
×
×
  • Create New...