-
Similar Topics
-
By SayHiToRambo
08 trooper 1100
Bit of background. First the machine would take for ever to start. So I adjusted the valve shims into spec and made sure the timing is correct. Starts perfectly now.
now it fluctuates on idle. Bogs down, Revs up, repeat. I noticed the fuel pressure drops from 60psi to 20psi while that happens. It also bogs down at the lower end of each gear, higher rpm seems to be fine. Seems to struggle under load. In neutral it revs up perfectly.
brand new fuel pump, fuel filter, gas. I noticed on the fuel pressure regulator there’s that vacuum nipple, it’s not attached to anything and I’m not sure where it would go. Possibly the problem?
Another issue is the tip off the end of the exhaust is broken off, sensor is still attached and connected. Could that cause these issues?
my next plan was to look into the pressure regulator and voltage to fuel pump while driving. Is there anything I’m missing or any ideas you guys have?
thanks!
-
By rocmoc
This is rocmoc/Michael one of the first on this forum when the Joyner was one of the most active topics. First an update of others. The earlier members will also remember Lenny and Jeff. With myself we organized the first Jamborees in 2009-2012. Sadly if you have not heard we lost both Lenny and Jeff in 2018. A great loss to the community. Myself: Still around but rolled over to Jeep and Arctic Cat Wildcat. The Wildcat design still remains me of my old 2008 Trooper. Doing well as the Last Man Standing but cleaning out the garage. Found some New and used Trooper parts I will list in the parts section. Wanted to give you all a chance before I list on Ebay. As many of you knew Lenny listed a lot of stuff on Ebay. Will I partnered a lot of the stuff with him and I still have stuff. Take care and I will check in for message should you want to ride. Still make it to Utah every other year and am still in Southern AZ.
rocmoc in AZ/Mexico
-
By Homeowner A
Have an issue all the sudden where the UTV will cut out randomly mid range throttle and under load. Light consistent throttle on fairly flat ground no problems. If you quickly change throttle position sometimes it will bog down and cut out, splutter, etc. Floor it or let off and it may do just fine. Going up a hill and adding more throttle as the incline demands, will cut out splutter and smell unburnt fuel. So far doesn't ever completely quit. If you let off it will idle just fine. A lot of times if you floor it, it will pick up and even get a boost of power. Changed to a slightly hotter plug to see if that would make a difference, but it didn't . Any ideas what might be going on and what to try next?
-
By BMurph
Hello everyone! I am new here and have no experience with UTVs but I am quickly getting some. I have a shifting problem where I can shift through all gears without the engine running but as soon as I start the engine I can not select a gear. Yes, foot is on the brake and yes the pin is being pulled to go into reverse if I was to try going into reverse. The shift lever does not move. I adjusted the linkage to get more accurate shifting with the engine off so I know those are now correct. I opened the shift lever housing to inspect the teeth on the gear and found this picture below. Why is this oil so milky looking? I assume with oil like this I'll need to replace the wet clutch as well but am not positive. Does anyone have any input into how to flush this system and get things shifting correctly? Thanks in advance for all the help!
-
By rsar
So I finally got my Quad Gear cab enclosure after waiting out the backorder for three months and to say it's been a huge disappointment is a pretty big understatement. I think mostly because I could make it work, if not for one major issue. The windshield is right next to impossible to see out of. It's a real headscratcher because the side and rear windows are okay. It's not high quality 30 or 40 gauge marine vinyl but I have Quad Gear's stand-alone winshield so I knew it wasn't the best in terms of visibility, but definitely doable for the price. Incredibly, the side and rear windows of the cab eclosure are just as clear as the stand-alone windshield. And the windshield on the enclosure is like 50 percent worse than the stand-alone. It's the same company! I don't get it. If it had just been the rear windshield that was that bad I would have kept it. There are some creases and wrinkles here and there, but I've been using the stand-alone windshield for the past three months so it's good enough not to have to shell out $600 plus for the stock hard windshield. I'd put visibility at about 65- 70 percent. The wife hates it though, which is a pretty big negative. In any case, my original plans were to have an upholsterer change the crappy vinyl out for the high quality stuff and I even sent it to a guy who ended up flaking out on me and refusing to do it. He said he didn't want to charge me $400 for something I paid $200 for. Long story, short, I decided to return it and just get the insanely expensive Kawasaki enclosure next winter since the frigid temps here are about to start climbing in a couple weeks anyway. I first put it on just to see how it would look (I took pics of course) and found that it didnt even seal 100 percent and made it drafty inside the cab. So make that two major issues. At least with the stock enclosure everything will be top flight. Doors will be nice too.
-
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now