Quantcast
Jump to content


Recommended Posts

Posted

I just bought a new Hisun 750 sxs. I drove one mile and it just died. No power at all. Battery is 12.8v. Found no blown fuses. No power to the panel, no nothing. Problem for me is I bought 160 acres near big bend. Trying to build a house. Got blown up in 'Nam . Can't walk much. Scared I'm way out and it fails again. I heard something  about a brake switch,  but I have no idea where it might be.

  • Alex changed the title to Hisun 750 Total electrical failure
Posted

Hi Nypto,

How are you with electrical troubleshooting?

Since you know the battery is good, Have you checked the cables?

  • Check continuity between the negative terminal and the engine case, you should have close to 0 ohms if the ground connection is good.
  • Check between the positive terminal and the starter relay on the other end of the positive batt cable.

I would be surprised if there wasnt a loose connection somewhere in there. Likely connected at the factory and not tightened, and it just rattled loose.

 

Past that I would try to lean on the people who sold it, and see if you can exchange it for a new one since you only got a mile out of it.

 

Let me know how the troubleshooting goes, and if you want to continue digging past that.

Posted

Sounds like the battery cables are good.

Ok you've checked the simple stuff, I would contact the seller and ask for an exchange at this point. It's only done a mile I don't think that's an unreasonable expectation.

If you want to keep going let me know, but from here you're likely looking at replacing parts and possibly voiding the warranty, as well as a bunch of time and labor.

Posted

Well, I have to show my stupidity here. I had the 750 towed. 150 dollars and I found out what the problem was.

The dashboard ECU switch fuse was blown. I NEVER thought a simple 5 amp fuse would shut the whole utv down.

Going to call the dealership and ask if it was a known problem.

I did buy a handful of these fuses just in case.

I appreciate the help you offered. I know where to come for help

THANKS

Posted

Yeah....that's  where my ignorance showed thru. I never thought to check a little 5 amp fuse that ran the display. How could that little fuse wreak havoc on my whole dystem?

I found out exactly how it happened. The little plug in the glove box..for accessories was unplugged. I had placed a pair of needle nose pliers in there which came into contact with the positive side of the plug. I now carry a handful of fuses.

  • 1 year later...
Posted

Hello Nypto.....I am having the same exact issue on my 2021 Axis 750 crew......can you tell me where the dashboard ECU fuse in question is located?  I am about to pull out my hair with this issue!

 

Thanx!~

 

West

 

Posted

Looks like this, gotta pull the screws and the fuses are inside. It's under the seat near the batt on the smaller displacement UTVs, and I believe under the hood on the firewall on the bigger ones.

If you look at the wiring diagrams a lot of stuff is shared so a seemingly unrelated fuse can cause issues on a lot of systems.

Screenshot_20220916-133508_SamsungNotes.jpg.02c220d81b7483b84f15f9e79b5c9a96.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • By Justine
      I've had a Hisun Vector E1 for just a bit longer than is required for me to do some maintenance. While it's well-overdue, it only drives 1.5km a few times each week on a fairly decent gravel road (to the letterbox), and it has worked really well right from the get-go.
      Looking at the manual it states that I need to use SAE80 API GL-4 Hypoid Gear Oil for the Main gear Case, and SAE80 API GL-5 Hypoid Gear Oil for the Front gear Case - unfortunately i can't find either of those online here in Australia. Plenty of options that look close, but, as someone who has never driven any vehicle before, I want to use the right thing and it's a tad confusing.
      My question: Since there are no oils that are bang on SAE80 (they all seem to cover a range) would Liqui Moly Hypoid GL4 Gear Oil 80W-90  & Motorex Hypoid GL-5 Gear Oil 80W90 - be ok to use? (Or any other suggestions of what I might be able to purchase online in Australia) And would I have to drain out any existing oil from both gear cases?
      This is a whole new world for me and  being able to find exactly what is specified in the manual hasn't made this easy!
    • By Poppateets
      I just purchased a used 2023 Massimo warrior UTV SxS 1000mx with 600 miles on it. I didn't even get a full day of riding and the driver's side rear axle broke. I'm pretty sure it was already going bad because we would hear a noise once in a while. I'm wondering if anyone else has had problems with theirs. Also looking for places to buy accessories.
    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
×
×
  • Create New...