Original Joyner brake parts available
-
Similar Topics
-
By Ken rung
Does Anyone by chance have a owners manual and a shop manual for a 2007 800cc trooper. I just bought one and need to figure out where and how to engage and disengage the 4 wheel drive. Is it electronic or is there a hidden lever. PLEASE HELP
-
By CYJSP2009
Dear Joyner owners
Any one who is looking for below Joyner parts please send email to casey from Leaf Asia ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
Currently, we have supply below parts:
1. cv axles, cv rebuild kits, cv boots
2. Differentials and differential ring and pinion set
3. Cables,
4. Brake parts
5. Engine parts
6. Other parts.
We will provide better price, close follow up ...
We can arrange productioni for parts that we can collect demands from customers
Have a good weekend
Casey / Leaf Asia
2023-11-17
-
By SayHiToRambo
I’m looking to buy a camshaft cover for my 08 trooper 1100. Can’t find ANYTHING online. Anyone have a parts machine or know where to buy one?
thanks
-
By BMurph
Hello everyone! I am new here and have no experience with UTVs but I am quickly getting some. I have a shifting problem where I can shift through all gears without the engine running but as soon as I start the engine I can not select a gear. Yes, foot is on the brake and yes the pin is being pulled to go into reverse if I was to try going into reverse. The shift lever does not move. I adjusted the linkage to get more accurate shifting with the engine off so I know those are now correct. I opened the shift lever housing to inspect the teeth on the gear and found this picture below. Why is this oil so milky looking? I assume with oil like this I'll need to replace the wet clutch as well but am not positive. Does anyone have any input into how to flush this system and get things shifting correctly? Thanks in advance for all the help!
-
By Alien10
This is the E Brake, the one that is on the center drive shaft rotor below the dump bed. It is NOT related to any of the wheel disc brakes.
A few months after purchasing my Coleman Outfitter 550 (Hisun) new, the E brake stopped working. Thought it had got water or oil on it as it gradually went from good holding to poor holding to literally NO holding. Been lazy using a piece of 4x4 to keep from rolling, but that's a pain. So, into the barn I went with work light to see what the heck is wrong. E brake pedal worked, but hit a hard stop and felt like the cable was froze up from rust but that was not the case. As it turns out the E brake is actuated by some kind of weird actuator lever/cam arrangement based upon the actuator lever being moved about 15 degrees from its fully released position. That makes the adjustment pretty critical with such little movement. Bolt "C" in the pic below is the adjustment bolt, held in place by lock nut "B". Working from below, here is what I did.
Removed the skid plate below the E brake. 6 bolts and washers. Next, looked at the brake pads which still had a good amount of pad left on them. Looked to be a little less than 1/8" each. Verified that the cable from the E brake pedal "A" actuated the E brake arm "D". Cable "A" pulls and released lever "D" in the direction of the curved arrow. Applied E brake and checked the actuator arm, it was all the way up with no bare cable "A" showing. Released E brake and checked the actuator arm, it was all the way down with bare cable "A" showing as in the pic below. That spring pulls the lever to fully released position. Note: I disconnected the release spring from at the lever with needle nosed pliers to make working with the adjustment easier to do without that pressure on the lever. With E brake released, loosened lock nut "B" and backed it off the lever about 1/8" or so. Tightened adjustment bolt "C" by hand just until it stopped. Retightened lock nut "B". E brake now holds securely on my hillside driveway, and releases completely. Reinstalled skid plate. Hope this might be of some help to someone as none of this is in the owner's manual or in diagrams.
up.
Released brake and rechecked the actuator arm, it was all the way down.
-
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now