Quantcast
Jump to content


Adjusting gas pedal height

jmutv

By jmutv
in Coleman UTV SxS Forum

 Share

Recommended Posts

jmutv Apprentice

jmutv

Posted
Posted

Hello there!  My 2022 Coleman 550x gas pedal is fairly high off the floor.  It seems to be common on all UTVs I’ve been in.  Perhaps there is nothing I can do because of the pedal travel, but anyone else feel it’s too high when driving slower speeds?  I have to keep my leg basically hovering to maintain speed.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • Alien10
      Snow Blade for Coleman Outfitter 550?
      By Alien10
      I'm thinking of buying a snow blade for my Coleman Outfitter 550 (Hisun with Coleman stickers).
      Has anyone purchased a snow blade that can offer the make and model they bought and any comments, pros  cons etc.?
      Not 100% sure I'm going to buy, as the selection of blades for this model seems a bit thin on line. 
      Thoughts and comments welcomed.
      Thanks in advance.
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • CYJSP2009
      2022 brandnew Joyner CV Axles and CV Joint rebuild kits are comming
      By CYJSP2009
      Dear Friends, 
      2022 Brand new Joyner CV Axles and CV  Joint rebuild kits are comming 
      1.  S650.03.02.02.00 ---Joyner 650 Commando Rear
      2. TR1100.03.01.03.00 --- Joyner Trooper Front 
      3. TR1100.03.02.03.00 --- Joyner Trooper Rear
      4. D650.03.02.02.00 --- Joyner 650 Sand Spider Rear Left 
      5. D650.03.02.03.00--- Joyner 650 Sand Spider Rear Right 
      6. SV800.03.02.01.00 --- Joyner 800 Viper, SV1100 Drive shaft Left
      7.  14274 --- 650 ider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      8. 15803  ---  650 Sand Spider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      Attached are the part photos for reference. 
      Above parts are now on the way to USA, will be ready for inland delivery in middle of July. 
      Price: CV Axle: USD250/ Piece;  CV Joint kit （without grease): USD110  send to door. 
      There will be special discount availabe for deals completed within July 2022.  
      Buy 1 piece: Get 5% discount, 
      Buy 2 pieces: get 10% discount.
      Buy 3 pieces: get 15% discount, 
      Buy 4 and more than 4 pieces: get 20% discount. 
      Please kindly note Qty for each part is not big  and it is hard to forcast when there will be next offer for these kind of products unless there is sufficient confirmed order qty for productioin arrangement. 
      Payment method: Payoneer payment link ( can pay through bank account or credit card) or Paypal ( [email protected]) .  Payment commission paid by the buyer. 
      Interested parties, please contact [email protected]. 
      Thanks
      Good Luck
      Casey / Leaf Asia
      July-07-2022
       
       
       














UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...