Quantcast
Jump to content


Recommended Posts

Posted

I ordered remote control hardware from Amazon https://www.amazon.com/dp/B07P2G4T22?psc=1&ref=ppx_yo2ov_dt_b_product_details and initially installed module behind the switch panel and wired it into the winch control switch.  After researching the 2014 HiSun service manual posted by another forum member, I discovered a better way to implement (fyi-this is not documented any Coleman service manual that I could find)  My UTV is a 2022 model, but the wiring appeared to be the same for my model. 

There was an unconnected Molex plug hanging under hood on the driver side (Molex#33471-3301), (see photo).  I purchased a Molex 3 wire connector ((Molex#216283-1032) directly from Molex  for $5.82 including tax & shipping.  This connector has the 3 wire pigtail to easily splice to the remote control module wiring.  https://www.molex.com/molex/products/part-detail/cable_assemblies/2162831032 .

I added a ground stud near the parking brake mechanism in order to connect the black wire from the module see photo) .  I added velcro to the module and then secured with zip ties to the back of the nameplate bracket (see photo). 

See the wiring diagram for hook-up that I used.  The loose blue wire is the antenna so it is not connected to anything.  

GroundStud.JPG

IMG_4159.JPG

IMG_4163.JPG

IMG_4164.JPG

IMG_4166.JPG

Molex Wiring.pdf

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • By BigWave
      I turned off the key and then tried to start it a minute later and it would not start. I changed out the fuel filter and the injector. still nothing. if i have the injector pulled out and close to the hole the injector will spray fuel into the hole and it will run but the minute you put the injector in it will die. any idea's please
       
       
      Bigwave
       
    • By Mike Jenkins
      I have a 2013 Hisun with a 686 Yamaha engine.
      I purchased it from an individual and it ran fine as long as the battery was full.
      I replaced the stator and now it will not start (run).  It cranks fine, has fuel pressure, but will not fire up.  I replaced the coil, no luck there.
      a technician told me that it was the wrong stator and wants a mint to replace it.
      the wires all plugged in when I installed the stator.
       
    • By HighSon
      This mod is not for the fainthearted, as it requires some basic metal fabrication and welding skills.  But the result is worth the effort IMO.  I chose an aftermarket Honda Talon windshield based on economy, size, and construction (aluminum frame, DOT glass, folding, windshield).  It fits OK, a little narrow at the top, and you need to incorporate the lower section of the original acrylic windshield and build some additional plates, but better than being too wide.  If you are wondering why I attacked this mod, it's because mine is driven daily on the street.  Tired of fading, scratchy, hazy plastic.  Sucks in the rain; sucks at night.  Now I can see.


    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
×
×
  • Create New...