Quantcast
Jump to content


Coleman ut400 battery light comes on when using the winch

Butcher6868

By Butcher6868
in Coleman UTV SxS Forum

 Share

Recommended Posts

aefron88 Community Regular

aefron88

Posted
Posted

It's not abnormal. The winch uses a lot of power, the charging light indicates battery voltage is low to tell you the battery isn't charging at that moment.

I'm not sure what voltage the light turns on at, but typically you should have 12.5-12.8V not running, and if the charging circuit is running right 14-15V. Below that the light will come on. As you use a lot of power the voltage will drop, triggering the light.

You may find your battery is near the end of its life cycle. If you don't run the machine at least weekly I highly recommend a battery tender to get a reasonable life out of the battery, and make sure it starts when you need it. All of my infrequently used "toys" have battery tenders.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Alien10
      Snow Blade for Coleman Outfitter 550?
      By Alien10
      I'm thinking of buying a snow blade for my Coleman Outfitter 550 (Hisun with Coleman stickers).
      Has anyone purchased a snow blade that can offer the make and model they bought and any comments, pros  cons etc.?
      Not 100% sure I'm going to buy, as the selection of blades for this model seems a bit thin on line. 
      Thoughts and comments welcomed.
      Thanks in advance.
    • Joseph Sills
      Panel Light Dimming ?
      By Joseph Sills
      Has anyone modified the panel lights so they can be dimmed ? I haven't found a wiring schematic for the display . 
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...