Quantcast
Jump to content


2020 Coleman 550 Bad Bearing and Pops Out of Gear When in Forward

JustinTexas

By JustinTexas
in Coleman UTV SxS Forum

 Share

Recommended Posts

JustinTexas Newbie

JustinTexas

Posted
Posted

I bought this from an auction not working and when you drive it forward it felt like it was poping out of gear and could hearing bad bearing noise from engine/trans. I knew the bearing noise was coming from trans or clutch so I went ahead and pull it out and apart to see what was going on. the bearing noise seems to be the one way clutch bearing so the clutch and drum are both messed up. is there any way that binding up would make the clutch disconnect or anything? do you know what else would cause that? i heard somewhere that you can just remove the bearing completely and it will just free spin down hill, has anyone done this? thank you so much for your help and advise

  • Alex changed the title to 2020 Coleman 550 Bad Bearing and Pops Out of Gear When in Forward
aefron88 Community Regular

aefron88

Posted
Posted

Does the bearing look like it physically failed? If it's intermittently failing it could cause drivability issues. I haven't experienced it myself so I can't comment on exact symptoms.

The failures I've read about it seems to start locking/unlocking at random and making a grinding noise before it shortly catastrophically fails.

Motorcycle Dr recommends cutting the spring shorter on the factory one way bearing to give it more spring pressure, if you dig around on their website you can find the pdf.

Yes you can ditch the one way bearing if you want.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • clint501
      Hisun E1 charger not working
      By clint501
      I recently purchased a Hisun E1 and the other day the charger stopped working properly. The LED on the dash blinks red & green and the light on the side of the charger also blinks red & green. The fan on the charger does not come on like it used to do. There is no error code that I can see. Does anyone have any suggestions to remedy this?
    • Will D
      Mule 4010 trans overheating
      By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 
    • mcraigchr
      550 - Diff fluid change and final drive?
      By mcraigchr
      Howdy y'all,
      I have the service manual, but it leaves me with questions.
      1)  It is time to change the diff fluid.  The service manual says 80w-90 for the rear and Dextron 3 ATF for the front!  Is that correct?  That seems odd to me.
      2) The service manual also speaks of the need to change the transmission fluid but gives no detail about it.  What needs to happen here?
      3). The service manual also discusses changing the final drive fluid with 80-90 Hypoid.  Is the final drive actually the tranny?
      Any details about the changing of the fluid or what fluid to use ... or even other things that need to be changed that the manual does not mention would be appreciated.
      Thanks,
      Craig C.  
    • bms stallion owner
      BMS UTV sluggish acceleration issues/ final gear oil maintenance concerns
      By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...