Quantcast
Jump to content


Recommended Posts

Posted

Hello, new to fourm.

I have a 20022 Honda Pioneer 1000-5 Deluxe.?

3 extra switches on dash for future use. My question are they pre wired in the engine compartment?

  • Alex changed the title to 2022 Honda Pioneer 1000-5 Deluxe Extra Switches

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Poppateets
      I just purchased a used 2023 Massimo warrior UTV SxS 1000mx with 600 miles on it. I didn't even get a full day of riding and the driver's side rear axle broke. I'm pretty sure it was already going bad because we would hear a noise once in a while. I'm wondering if anyone else has had problems with theirs. Also looking for places to buy accessories.
    • By Eagle Mountain Outfitters
      Our R&D team just finished the first unit and wanted to show you guys. Need more cargo space without losing the functionality of being able to fold down the seat to use the full bed? Eagle Mountain Outfitters, the maker of the original metal UTV roof, has designed a foldable rear cargo basket to meet your needs. Price is $625 + $30 shipping.  If you have any question's, please reach out to me at [email protected]
       

    • By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • By Reynolds Rocket
      I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 
    • By lmarkie
      I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
      Only problem is the exhaust exit is toward the back seat instead of out the back.
      Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
      Any thoughts?
×
×
  • Create New...