Quantcast
Jump to content


Recommended Posts

Posted

I bought a 2021 Coleman 400 UTV from Tractor supply mainly because of the $2000 off black Friday sale ($6999). I wanted something to do some light hauling around the boat shop and figured this would be a better choice than a golf cart. Initial review is that for the money,it's got to be the best deal going. Fully equipped right out of the box with a lot of nice features. First off,everything worked,that's a good thing. First thing I noticed is that this thing is LOUD,so loud that I use foam ear plugs to run it. The rear axle is locked,like most 4 wheelers,so the tires scrub on tight turns and will tear up the lawn. I found some loose bolts and did a general inspection of everything and tightened up the loose ones as I found them. It's cold here in SE Michigan and I want to do some recreational use during the winter. I bought a 3 Star door and rear window soft enclosure and installed it. Top quality materials and fit great. I added some foam to close off all the gaps and it really does the job. Next I added a Ice Crusher heater kit that uses the coolant to provide heat in the cab. Quality parts and the kit was pretty much complete,I also added a coolant shutoff valve so I can direct all the coolant through the heater instead of the radiator,or blend it as I wish. The heater has a 3 speed fan and 2 directional outlets for this model and with the enclosure will warm it up to shirt sleeve temps at speed with the outside temps in the low 30's. I also added a Kolpin Stealth 2 auxiliary silencer, the exhaust note is definitely quieter and less raspy, but this rig is still noisy enough at speed that you need ear muffs or plugs. I changed out the headlight bulbs to LED's which are a big improvement from the halogens. I figured out a trailer hitch adapter for the oddball thing Colman provides. Now it's just run it in and break it in. For a 400, it is actually quicker and faster than I expected,the specs say 38, but it's closer to 50. Brakes are powerful and smooth. The solid rear axle makes this thing pretty capable,but you also have the push button 4 wheel drive and a push button front diff locker if you need it. All in, it's set up just the way I wanted it for under $8000.

  • Like 1
Posted

Welcome.

If you have any questions there's plenty of info in the coleman and hisun forums (it's a rebranded hisun, but most of the 400 posts are in the coleman section) there's a couple posts in each about things to help quiet these machines down.

People have had good luck with adding various sound deadening materials under the front/sides of the seat and under the bed.

I would love to see a post about the heater setup with some installed pics. I've seen them listed but you're the first person I've heard of actually installing one on a 400.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Homeowner A
      I have a Coleman UTV 400 and looking for something to store it in.  Preferably something vinyl or plastic with its own base that can stand alone outside and house the UTV.  I think the dimensions of the UT400 are around 106" long 52" wide and 74" tall. 
      What should I consider that won't break the bank?    
    • By Howard Elmore
      I have owned mine for a couple years now but newer took off road.  How well does it do trail riding m?
    • By rev6engines
      Black Friday is here, and we’re excited to give our offroad family 20% off on all parts and kits! Whether you're prepping for new trails or just fine-tuning your rig, we've got what you need to keep rolling. Now Is also a great time to upgrade your sled, winter's coming fast!
      If you have any questions or need help finding the right part, feel free to call, text, or email us. We’re here for you!
      Call or Text:
      801) 489-8697
      Email at:
      [email protected]
       
      Happy riding!!! 🤘

    • By Will Sutton
      I've got a 2023 UT400 (bought from tractor supply) and I've been beating my head against a wall with it.
      It will start and idle perfectly. The second I touch the throttle it sputters and dies.
      I've checked that the fuel pump is working  (it is).
      I've replaced the injector, throttle position sensor, O2 sensor, and intake air sensor. All with no change.
       
      I've just taken a look a the schematic, and there is a crank position sensor as well.

      Could this be the source of my troubles? If so, where is this thing located? I can't seem to find it on any drawings from the parts suppliers.
    • By Greg Kilgore
      Last year bought a small universal coolant style cab heater. Well I installed it today. Thanks to another member, RangeRider45, and his install
       
      That told in his post the size fitting he used. I got the same fittings plus a few others. And all went kinda smooth. Took a few minutes to get air purged from coolant system. Should have parked on hill with front up in the air. But would have had a hard time working on it.
      I had a variable power switch connected to an overhead cab fan. Never really used the fan that much. And I have to remove the fan to put on my cab enclosure anyway. So I repurposed the switch to supply power for the heater. The heater has 2 12-volt DC computer fans that are rated for 1.8 amps each. So it's not going to be a big drain on the weak charging system. And with the switch I've got great control over the speed of the fans.
      If anyone is interested the radiator hoses are 7/8 inch. I reworked the temperature sending unit (moved it closer to radiator) to make room for all the extra plumbing I did to get the heater to work the way I wanted. 
      Plumbing parts list.
      10-15 worm water clamps. 3/4 to 1 1/4 inch size.
      2 1" x 3/4" x 1" PEX Tee
      1 3/4" PEX ball valve
      1 1" PEX ball valve
      5/8" heater hose. I got 6' and probably have 4' left over.
      I used the radiator house I cut out to use as splices between the PEX fittings. The PEX fittings are not true to their dimensions that are stated on the package. So they fit the 5/8" and 7/8" very nicely.
      They way I have it plumbed is from radiation out side. A tee, then the 1" ball valve, then a Tee. Coming off the Tees are the hoses going to the heater core. There is a 3/4" ball valve on one of the Tees. The ball valves are used to bypass the heater core in the summer. Or direct the hot coolant through the heater core in winter. The temperature sending unit tells me how hot the coolant is. And if anything is getting too hot. The dash also has an idiot light that comes on if the head gets too hot. But doesn't do anything if the radiator gets too hot. There is a temp sensor on the radiator that controls the electrical fan. But if the coolant isn't circulating. That switch never sends a signal to turn on the fan. But enough talking/rambling. Everyone wants to see pics. The only thing I need to change is the orientation of the handle on the 1" ball valve. I have 2" or more clearance between the handle and the tire when cut hard right. But I still don't like it. And instead of taking the valve out and rotating 180°. I'm just going to take the nut off and rotate the handle 180°. Think I need to make a locking mechanism to lock the handles in place so they don't vibrate closed when the machine is moving.
      The temperature sending unit and housing. Size 22 mm. Aluminum from Amazon.

      Upper Tee the lower Tee is identical. Can also see the handle of the 3/4" ball valve on the 5/8" hose going to the heater.

      The 1" ball valve. Goes between the 2 Tees

      Wide view of the plumbing.

      The heater installed in the sxs. The 3 black hoses are just hanging there. Zip ties to the heater but not attached to any thing. Will probably just direct 2 toward the wife's feet. And 1 toward mine. Or what ever is need as the heat is needed on rides. The black hose in passenger floorboard is some 1" hose that is not needed. Don't know what I'll do with it.

       
      I think if I was going to do it again. I'd put some Indian Head gasket dressing or silicone on the 1" side of the PEX fittings. And I may still do that. But I really hate the ideal of introducing air back in the coolant system.
       
      Any questions just ask. It may take a while to answer. But I'll try.
      Ya be good and stay warm over the next few months 
       
      Kilgore.
×
×
  • Create New...