Quantcast
Jump to content


Wheel Spacers/Ranger 570 Full Size Crew

Matt Tousley

By Matt Tousley
in Polaris UTV SxS Forum

 Share

Recommended Posts

Matt Tousley Newbie

Matt Tousley

Posted
Posted

Looking to install wheel spacers on my 2023 Ranger 570 Full Size Crew….2” lift  with a 28” tall tires.

Dealership tells me that the rig has 4/156 wheel pattern with 3/8x24 lugs but no one can tell me the bore size.

Also, any suggestions on which brands are the better of the bunch??

I appreciate any help.

Matt

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind
    • Duncan
      utv tires
      By Duncan
      I got a utv from lowes it has one tire in the back that is the same size as the front tires so it has 3, 26-9-14 and 1 26-11-24. i want to change the rear tire to the same one as the other.So instead of buying a new rim will a 26-11-24 tire fit on a 26-9-14 rim.
    • Troy C
      2012 Polaris Ranger 800 Convert to EV
      By Troy C
      I am new to forum but I have a 2012 polaris ranger 800 that motor went out and had it replaced and a year later here i am again so i am interested in converting it to EV . I am 72 but pretty active and live on 500 ac of land  that part is in hills but most is in low land. I have no idea what i need or want so any advice will be appreciated. Thanks guys 
    • Gerals
      2017 Massimo 500 that is locked in 4 wheel drive
      By Gerals
      I have a 2017 Massimo 500 that is locked in 4 wheel drive don’t know if the switch is working or if it’s something else does it have a fuse for the switch 
    • Brett
      2006 Polaris Ranger 700 side by side idles fine but dies when you touch the gas
      By Brett
      Fuel injected 700 starts great and idles great but touch the gas and it dies

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...