Quantcast
Jump to content


Recommended Posts

Posted

I have an 800SX 2021, 40 hours on it and No belt noise.  I have recently noticed some “squeaking” in the shocks and could be some mud or dust, more noticeable on cold days.  No problems otherwise, starts easy, never stalls.  The belt drive transmission does seem to jerk into gear as you first start moving, engine needs to reach a certain RPM before the gear engages and its not smooth when you first start moving — but is very smooth afterwards,,,,,it’s just sort of “snaps” into gear.  Ive heard thats a common complaint and not a mechanical issue or problem...its the only thing I don’t like about the Tracker

Posted

Thanks

I have the same noise from the shocks.  I think only when they are cold.  After everything warms up n it is fine.  Dealer replaced the  drive belt cover. Said it was rubbing.  Haven't had it out yet, we'll see

  • 6 months later...
Posted

Had the same squealing/chirping noise with mine. It was in the shop numerous times. The primary clutch was replaced, the secondary clutch was replaced, the belt was replaced and the problem was not resolved. Fast forward to the lasttrip to the shop and they did some sort of shimming and adjustment and it is much better. It will make noise for about the first 30 seconds then goes away for the entire time I use it. Start it the next day and same thing. I’ve decided to just live with the 30 seconds of noise every day!

Posted

Curious to know kind of shimming they did.  They replaced everything on mine.  I just decided to give it a little and let everything get broken in.  Not too bad right  just wait and see what happens.

Posted

I guess I am somewhat fortunate since i have Not had any squealing on my 800 SXLE - yet.  Mine was bought New in 2021 with about 60 hours on it now.  It has not been ridden very hard but does get some mud, water and dust on it and I’ve never power washed it — just hose it off.  Others have said to power wash the under carriage — good idea but i’ve Not done that yet. 

Posted
On 9/13/2023 at 9:44 AM, chuck92308 said:

Mine is a 2022 and got about 1200 miles on it.  Been doing it since day 1.  

Good luck with yours

Thanks

 Chuck

Annoying for sure, but I’m not going to worry about it. I bought an extended warranty so if something should eventually fail, I’ll be covered.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • By Texjpr
      2002 ranger 500 4x4 stopped running and wouldn't restart. Service manual wiring diagram helped identify the hub safety switch as the culprit. Using jumper wires to bypass  switch allowed the engine to start and run normally. Inspection of switch showed melted epoxy and a strong smell of burnt electrical. Unable to find replacement part either used or new. Is there a work around other than jumper wiring?
    • By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
×
×
  • Create New...