Quantcast
Jump to content


Vector 500 Popping Noise

Charlie Shew

By Charlie Shew
in UTV General Discussion

 Share

Recommended Posts

Charlie Shew Newbie

Charlie Shew

Posted
Posted

I’m at a friends, his vector makes a popping sound while the engine is under stress. It does not do it in reverse or accelerating down a hill. We replace the belt but that did not fix it. Any suggestions. I’ll try to attach a video

  • 2 weeks later...
Pascal posive Newbie

Pascal posive

Posted
Posted

It's difficult to determine the exact cause of a popping noise without further information or context. However, here are some possible causes of a popping noise related to the Vector 500:

  1. Suspension System: The Vector 500 has a suspension system that consists of shocks, springs, and other components. If any of these components are worn out or damaged, they can cause a popping noise when driving over bumps or uneven terrain.

  2. CV Joints: The Constant Velocity (CV) joints are responsible for transferring power from the engine to the wheels. If the CV joints are worn out or damaged And  UTV accessories they can cause a popping noise when turning or accelerating.

  3. Exhaust System: A loose or damaged component in the exhaust system, such as the muffler or catalytic converter, can cause a popping noise.

  4. Transmission: If the transmission is low on fluid or has worn out gears, it can cause a popping noise.

  5. Brakes: Worn or damaged brake components, such as pads or rotors, can cause a popping noise when applying the brakes.

If you're experiencing a popping noise with your Vector 500, it's best to take it to a certified mechanic for diagnosis and repair.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • aefron88
      HOWTO- Code Scanner & Read Engine Parameters
      By aefron88
      This post will explain how to hook up your PC to the ECU of a Hisun/Coleman/Etc UTV to be able to read error codes & engine parameters for troubleshooting purposes.
      This is applicable to all small engines using the Delphi MT-05 ECU. This should cover all fuel injected Hisun models, as well as various other Chinese FI engines, as the Delphi MT-05 ECU seems to be the favored ECU solution.
      Even though we get actual engine error codes to display on the dash, sometimes we have “pending codes” (not yet confirmed by the ECU) or other intermittent issues that are hard to diagnose, for example a poorly connected sensor that may give intermittent false readings, or a sensor that’s putting out bad date, but not bad enough for the ECU to realize.
      The setup requires 2 cables, which are available for around $25 combined, a PC with a USB port, and some charityware software called “HUD ECU Hacker”. This gives the same functionality as the $300 dealer code scanner for a fraction of the price.
      In searching I found info about HUD ECU Hacker, but I have yet to see info anywhere about how to hook it up to a Hisun, so I took the leap and bought some cables, and made it work. I will show a step by step of how to do so in post two.
      I will be breaking this down into 2 posts:
      Delphi ECU Info & Overview (This post) System setup & use Delphi ECU Info (Skip ahead to the next post if your eyes glaze over technical details)
      The Delphi MT-05 ECU was developed to allow small engines to use fuel injection. A fuel injection system requires feedback from various sensors to operate efficiently. This feedback allows the adjustment of ignition timing, fuel injection volume, etc to efficiently and cleanly produce the most power possible from a given engine.
      The MT-05 ECU has a number of sensors that are required for proper functioning including; Coolant temp, crankshaft position, intake temp, intake pressure, exhaust O2, throttle position, as well as some other optional sensors that are used on more complex vehicles.
      From the sensors the ECU adjusts: Fuel injector timing/pulse, Idle air control valve, and ignition coil

      The Delphi MT-05 puts out diagnostic data, however it is not ODB2 like a modern car, where is where it gets tricky reading it. There are three options, there is an old 16 bit piece of software Delphi has that is not able to run on a modern computer, there is the motorscanner tool for dealers ($300), or there is freeware HUD ECU Hacker with the proper cables.
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.
    • Graffy
      Transaxle X Engine
      By Graffy
      Im new to the UTV world but not new to the fabrication world. Me and my friend have been focusing on designing and building a rallye-type setup with a custom chassis and a single seater. With suspension design at a good point, we want to start work on the chassis; however, there is one big hiccup in the way, and that is the powertrain. We've been going back and forth on this for quite some time now and realized that we cant find any great options. We want the engine to be behind the driver and mounted between the seat and the rear axle with a transaxle setup. We aren't going to need any power for the front wheels, as this is an RWD application (Toyota MR2 style setup). It also needs quite a small engine; I would love for it to be 100+ hp and possibly be turbocharged down the line, but power isn't a huge deal right now. Right now its a battle between a UTV engine X trans or a bike engine with a diff.
      Although crotch rocket engines are super cool, they aren't built for high-torque applications, and a differential setup for one can range up to $6k, which is pretty ridiculous for our initial budget. (We are not going chain-driven as we have bad experience in that area.).
      That's what leads us to UTV x Snowmobile drivetrains. I was initially surprised to find out how much power they have and realized it could be a great option with how they are designed for high torque applications. It is a difficult situation to find a good setup. 
      The transaxle needs to be either a manual or a sequential setup. And although there are some great engine options, with my limited knowledge in the UTV world, I have yet to find a transaxle that fits or works well with those engines.
      So my questions are this: Does anyone know of a good combo or might be able to lead me down a direction? Could it be damaging to an AWD transmission if nothing is connected to the front output shaft and only the rear diff?
       
    • dman66
      2018 Coleman UT400 Trans keeps popping out of forward
      By dman66
      My buddy has a ut400 that the forward gear keeps popping out of gear. She only has like 400 miles on the odometer .the shift cable has been adjusted and the shift lever has been updated / modified. All other gears are good. Is there an internal detent cam or something that wears out or shift fork that can be replaced ? Or is there some other magic that I can perform ? Looks like the engine needs to be split.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...