Quantcast
Jump to content


Hisun Strike 250 complete electrical failure


Go to solution Solved by Cody Brown,

Recommended Posts

Posted

Not sure how better to describe it other than no lights, head lights, dash lights, no cycling of fuel pump when the key is turned, no starter activity, etc.  checked all fuses in the fuse box under the driver seat (anyone know of any other fuses I might have missed?).  Hooked starter up directly to the battery for a split second and it cycled fine.  Same with the radiator fan.  This machine was running fine during a ride, and my son hit a bump, it died, and never came back.

Posted (edited)

Sounds like a loose connection somewhere in your primary 12 volt supply or ground. Do you have a service manual with a circuit diagram and a good volt meter? I'd start at the battery, test for 12 volts from the positive terminal to a ground somewhere on the engine or frame. If you read 12 volts, your ground is probably OK. Then start testing from your battery ground to the ignition switch to see if you're getting 12 volts there. Someone with other ideas will hopefully chime in. You'll need a wiring diagram to check much further than that.

Looking at the diagram for my 550, it looks like the horn is hot all the time, yours may be also, does it work with the key off?

Edited by Dale Stansbery
Additional ideas
  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • By clint501
      I recently purchased a Hisun E1 and the other day the charger stopped working properly. The LED on the dash blinks red & green and the light on the side of the charger also blinks red & green. The fan on the charger does not come on like it used to do. There is no error code that I can see. Does anyone have any suggestions to remedy this?
    • By Matthew Smith
      2013 Bennche Bighorn 700 EFI
       I just picked up this project that I was told would crank, but not start.  This is what I’ve figured out so far….
      I installed a new battery and get all dash lights, head lights, and brake lights on when turning the ignition on.  Fuel pump even turns on.  It does not crank with the key, but would when I jumped the starter solenoid, so I replaced it…..no change.
      Figured I’d check for spark and compression while I was dorking around.  Compression is 150 psi, but there is no spark.  Replaced the spark plug… no change.
      So, is my new starter solenoid bad?  Could it be the brake or gear position switches even though the brakes and neutral lights come on?  Not sure where to go from here.




    • By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
    • By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 
×
×
  • Create New...