Quantcast
Jump to content


UT400 - Ran out of gas, cannot restart

Kenbaz

By Kenbaz
in Coleman UTV SxS Forum

 Share

Recommended Posts

Kenbaz Newbie

Kenbaz

Posted
Posted

Well, the subject says it all!  After the motor stopped, I went out and bought gas and filled the tank.  Tried to start and it just cranked - no fire. I assumed I had spark, because nothing changed there. I pulled the plug and could not smell gas. The plug was dry. Put it back in and tried to flood it by piumping the pedal, but it was still dry when I  took out again. 

   The gas gage red fuel lights didn't seem to recognize that I filled the tank (see previous fuel Haugen posts).  Disconnected and reconnected the negative battery terminal hoping it would reset any interlocks that might be set. Now the ignition panel will not light up when ignition turned to "On".  Things are getting worse instead of better!  Have the fuse panel open, will check fuses tomorrow. Can anyone help me get back on track?  No shop here in Tucson will work on it!  Nice unit. But you're on your own for maintenence. Thanks for any help!

  • Like 1
Kenbaz Newbie

Kenbaz

Posted
  • Author
Posted

Day 2 Update:  Went through all the fuses today. The fuse for the instrument cluster is not only blown,  but keeps blowing as soon as I turn the ignition to "On".  The only wire bundle I am unable to see is the one from the gas tank that probably goes to the fuel gauge.  I should mention that we live in a rural area and have Prarie dogs and packrats. The sxs is full of pea pods!  Lots knows what they've chewed.  Thank you for advice or sympathy...

  • Like 1
  • 2 weeks later...
jmutv Apprentice

jmutv

Posted
Posted

Hello there!  That sounds awful!  The potential for shenanigans from critters sounds like a decent potential.  Do you have a continuity checker?  Have you checked voltage on the battery? 

Kenbaz Newbie

Kenbaz

Posted
  • Author
Posted

Thanks for your reply!  We found the problem after removing the drive shaft tunnel cover and floor panels. Pack rat had totally chewed the electrical lines coming from the gas tank to the instrument panel. Also totally chewed thru the fuel line. Fixing connections should remedy problem. Thanks again. 

Kenbaz Newbie

Kenbaz

Posted
  • Author
Posted

Slowly getting things fixed. UTV sits outside,  and although it's shaded, it's still hot out for a 76 year old guy (mid-hi 90's). Will have new fuel line hooked up by tomorrow,  then have 4 wires to add new lengths of wire - 8 solder joints. Then reconnect battery and start 'er up.  Fingers crossed...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • hisun junk
      2017 Cub Cadet Challenger 750 hisun junk motor
      By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • TPlummer
      Axis x550 02 sensor on right after buying the UTV.
      By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • John M in Louisiana
      Hisun E1 Power Plug Replacement
      By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...