Quantcast
Jump to content


Automatic Transmission for Trooper

Guest Lenny

By Guest Lenny
in Joyner UTV SxS Forum

 Share

Recommended Posts

Guest Lenny

Guest Lenny

Posted
Posted

Rocmoc, I did some checking and I beleive there are at least a couple of transmissions available. Look at this site.

http://www.cheryacteco.com/en/article_list...=11690974580001

I beleive the QR512 is our transmission however it is slightly different, I suspect ours is the same bolt up pattern but has a lower low gear. QR512 is more then likely for an automobile application. The QR512E is more then likely the automatic version of it. If we can find out what american cars use their automatics coupled to small engines, I'll bet a match could be found. I sent an email to Chery fo find out more. If you look at the engines on their site, they have a great 1.9L diesel that could be coupled to their QR631 6 speed Trans. I think you could squeeze it in and have 3 times the torque. Maybe better to just start from scratch and built the whole thing over. In 2007, Chery entered a contract with Fiat to provide them with 100,000 engines per year.

Lenny

rocmoc Grand Master

rocmoc

Posted
Posted

I have this site also and went to a Chery Forum trying to get info for a source. I had no luck. I believe the cars are not available here in the States. I don't know where you would run one down. If I start changing things that much, I will go with Honda, Subaru or someone more USA mainstream. Good luck, this is a tough one!

When I was at Moab; power was not the issue, gearing was. The only place I need more power is in the sand and I'm not in it that often. We'll see how I feel about that after this trip as Rocky Point is going to be mostly in the sand.

rocmoc n AZ/Mexico

  • 3 years later...
scimaro Explorer

scimaro

Posted
Posted

Ok, does anyone have an answer to why I cannot shift gears when the temp drops below forty degrees? I know most of you Joyner owners live in the south, so I'm hoping someone traveled to the north and can help me fix this problem. Otherwise, does anyone know where I can get a cheap auto transmission?

nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted

Ok, does anyone have an answer to why I cannot shift gears when the temp drops below forty degrees? I know most of you Joyner owners live in the south, so I'm hoping someone traveled to the north and can help me fix this problem. Otherwise, does anyone know where I can get a cheap auto transmission?

First thought that comes to my mind is the fluid.. it get thick under 40 degrees mine get hard to shift in Iowa winter too. I would recommend synthetic fluid in transmission that can tolerate cold tempatures..I'm not sure if trans take gear oil or atf, someone here would know

Sent from my DROID RAZR using Tapatalk 2

nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted

Anyone with automatic trans for trooper?

I have heard there was supposed to be an cvt for trooper but i never saw or heard anything more. You could try asking klung motors.

I'm also wondering if anyone know of a rebuild kit i can get for the trans later down the road? My trans like to pop out of gear sometimes when i let off the throttle

Sent from my DROID RAZR using Tapatalk 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • FTG-05
      Want a new work UTV; who and what should I look for?
      By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • tuell
      Transmission will not engage
      By tuell
      Hi everyone I have a 2016 hisun vector 550 with 1320 miles on it I recently replaced the clutch the bell the belt the one way bearing basically everything inside the primary and drove approximately one mile my side by side just stopped pulling... no noise no smoke nothing the belt is still good but it's like the transmission will not engage in any gear any help would be greatly appreciated.... I have lifted the rear end and started the side to side put it in gear Wheels do not move but you can turn them by hand
    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.
    • Greg Kilgore
      2021 Axis 500 Head Bolt Torque specs
      By Greg Kilgore
      Got a 2021 Axis 500.
      I'm needing the head bolt torque specs.
      Manual states 38nm.
      But saw a video Hisun put out on YT for a 550 stating 50nm + 45° turn of wrench. Didn't think they would be that much difference on a 500 and a 550.
      Seen another YT video on a 2013 500. He did 38nm.
      Really only want to do this job once and done. And done correct.
      Anybody got the answer?
      Going to start this rebuild in a few once this weather brakes. Flooding and then snow and cold here now. But spring is around the corner and the wife has to have this fixed or a Honda pioneer may be parked in driveway soon. She has to be able to ride.
       
    • CRV
      Need some help. Looking for some parts too
      By CRV
      Howdy new member here . My hobby's Rabbit dogs , gamefowl . I'm retired from my real job but I stay busy with the hounds and gamefowl . So to help around the farm I ran across an old 2007 CC Big Country 4x2 to haul feed , water , sprayer and my sorry a$$ .It is in pretty good shape , 781 hrs. good plastic , tires, ect. . But as anything outside and 18 years old it needs seats ! The thing I have found wrong mechically the Diff. Lock Acturtor is broken where it mounts to the bracket ( partly why Im here ) . Hoping someone here can help  ! Just my wish list but Id like to find a roll cage and a composit/plastic top for it Im thinking I'll need a donor to salvage these things from ( again partly why Im here ) .Is there another brand that uses this same actuator? If anyone reads this and has or knows of any of threse parts PLEASE HOLLER !! 
      Again Howdy brothers & sisters

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...