Quantcast
Jump to content


Axis 500 Hill Climb

NCPonyboy

By NCPonyboy
in Hisun UTV SxS Forum

 Share
Go to solution Solved by that guy from Canada,

Recommended Posts

NCPonyboy Newbie

NCPonyboy

Posted
Posted

Hello, new Hisun Axis 500 owner here. I have a 2020 in the Mountains of North Carolina. It runs fine and I enjoy it but it seems to struggle on the hills. Granted I have one that is pretty steep but you could get out and walk faster than it goes up. I sometimes wonder that if I had anything in the bed it might not make it. So first question is, is this normal for these? Second question is, is there anything I can do about it? Maybe a power adder or chip tuning? 

 

Appreciate your thoughts

 

 

Andy Dickerson Apprentice

Andy Dickerson

Posted
Posted

I just went through this with my axis 700 and ended up purchasing a Hunterworks cvt upgrade. I also use mine in the mountains of NC and even the 700 isn't geared for the mountains. No chip is going to makeup for this as they are just under powered for this purpose. The CVT clutch upgrade changes the gearing I would say significantly lowering the gearing for climbing hills. It will also drop your top end as well. If you go with a Hunterworks upgrade clutch you'll need a new belt as well. 

If you are running this in the mountains you need to keep your UTV in lower gear. If you run it in high hear you'll destroy your clutch quickly. 

  • Like 1
Andy Dickerson Apprentice

Andy Dickerson

Posted
Posted 
Sales Rep:          NC                                                      

    Activity            Qty              Rate               Amount        
660 Sheave Combo         1              425.00         425.00T

I don't know if this will fit the 500. I think you will have to do a little research to compare if the same CVT clutch is used on the 500/700 axis machine. I think it is.

 

  • Solution
that guy from Canada Contributor

that guy from Canada

Posted
  • Solution
Posted

What Andy said is true.

Dollars to doughnuts, almost all chineese knock off ATV and UTV are simply underpowered and geared to high.

Clutch mods help but best just to use low range gear, be sure cooling system is all good however because you revs will be high and cooling is sub standard, many i have put cooling fan on direct ignition relay, bypass temp sensor, so its just on.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • ToughLuck
      2021 Massimo MXU 1000 Runs Rich
      By ToughLuck
      I have a 2021 Massimo MXU 1000.  Last winter the front drive shaft sheared off inside the motor and it was cheaper to buy a new motor than to take it apart in order to remove the front drive shaft that was broken inside the case…
      Now it is running rich, seems to maybe be geared too high, does not accelerate well once you hit about 28mph.  I’ve replaced the O2 sensor.  MAF is next (I accidentally ordered the wrong one, but when I removed the old one you can clearly smell fuel).  
       I’m not a motorhead but I can turn a wrench.  Any ideas how to get this motor optimized?  The motor has about 300 miles on it.  I broke it in as recommended in the manual. 
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Prepper
      2015 MSU-500 crank - no start
      By Prepper
      I'm working with a 2015 MSU-500.  Basic symptoms are it cranks well, but will not fire.  It has spark, and it has fuel spraying out of the injector (and spraying starting fluid into the throttle body and plug hole makes no difference).  It has compression.  I bought it not running, and no other information was available.  It has 775 miles on it and 127 hours.  It looks to be in very good shape.   Previous owner replaced fuel pump, ECU, coil, plug, and the fuse/relay box that mounts on the firewall, then gave up.
      My questions relate to cam/valve timing, considering the symptoms and diagnostics so far.  My thinking was the woodruff key sheared off and the crank spun, making it out of time.  My question is, by the pictures attached does anyone have an opinion as to the cam/valve timing being correct?  In the crankshaft picture you can see a timing mark visible.  In the camshaft picture I have arrows directed towards what I think are timing marks (which appear to be exactly 180 degrees from one another).  However, the long arrow in what appears to be bolt configuration in line with the piston/rod line.  Here is a puzzling note... in the position you see in the pictures... I have valve lash on both the intake and exhaust.  I think it's at TDC, given the visible crank timing mark and valve lash on both valves. 
      Any thoughts ?  Does this appear to be in proper valve time ?  Have I missed anything simple ?  Thanks in advance for your input.


    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Bobbers
      Axis 500 parts
      By Bobbers
      My wife accidentally ran the Axis 500 into a fence and tore the front end up (broke her arm too). Just wondering where the best place to get front end parts? I know she busted the knuckle but haven’t jacked it up yet. Thanks guys for any help!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...