Quantcast
Jump to content


ITP commits to ultimate test: the Baja 1000


Recommended Posts

Building on a winning performance in June at the Baja 500, ITP and parent Carlisle Tire & Wheel Company will be putting their products to the ultimate test at the upcoming Baja 1000. ITP and Carlisle have partnered with DragonFire Racing to tackle this historic event in a specially prepared Kawasaki Teryx. The driving team is composed primarily of ITP/Carlisle employees, competing in the UTV Sportsman class. Their car, #1801, will be using ITP’s rugged BajaCross tires mounted on ITP’s new T-9 Pro Mod spun aluminum wheel. This wheel was developed as a direct result of experience gained in the Baja 500. Additional backing for this entry comes from Black Rock off-road wheels and Ultimax performance belts. A similar car, #1803, is being fielded by the same Team Green Kawasaki DragonFire Racing crew that won the Baja 500. The teams will share pits, equipment and other resources.

This 42nd Annual Tecate SCORE Baja 1000 consists of a rugged 672-mile/1000-kilometer course that starts and finishes in Ensenada and travels much of the northern half of the majestic Baja California peninsula. More than 275 entries are expected, from 34 states and 12 countries.

The motorcycle and ATV classes will start their journey at 6:30 a.m. (Friday, Nov. 20) with the car and truck classes starting at approximately 10:30 a.m., or three hours after the last ATV leaves the line. The UTV Sportsman class will be the last to start, and will certainly have a considerable amount of night driving in store later in the event. Vehicles will leave in 30-second intervals in the elapsed-time race and the fastest finishers are expected to complete the course in approximately 13 hours. All vehicles will have a 31-hour time limit to become official finishers in the legendary adventure. The ITP/Carlisle #1801 entry will be carrying a GPS tracking system, so the team’s progress can be followed at this web page: http://www.trackinginternational.com/site/score/tracking/.

Pre-race festivities are on Thursday, Nov. 19, including the vastly popular tech and contingency of all vehicles and the SCORE Manufacturer’s Midway, to be held from 9 a.m. to 5 p.m. on Boulevard Costero in front of the Riviera del Pacifico Cultural Center.

This year’s Tecate SCORE Baja 1000 will be televised on a delayed basis as a one-hour NBC Sports special, in association with SCORE and Aura360, for the sixth consecutive year, scheduled to air at 2 p.m. (EST) on Sunday, Dec. 19, on the NBC Television Network. It will also air on a delayed basis outside of the U.S. on ESPN International.

For more information regarding the series, contact SCORE at its Los Angeles headquarters 818.225.8402 or visit the official website of the 2009 SCORE Desert Series at www.score-international.com.

For more information on ITP’s BajaCross tires, T-9 Pro Mod wheels and the complete line of the brand’s award-winning products, visit www.itptires.com.

b5-LLwHDDvs

View the full article

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Josh5696
      So I've got a 2022 Axis 500 UTV with only 50 miles on the odometer. It seems to have a strange grinding/squeeling noise coming from the clutch when decelerating or going down hill at lower speeds. Did some research, and found out this is apparently a fairly common thing. Alot of sources suggest the one way bearing is responsible. I'm hearing about quite a few horror stories about these bearings going bad on practically new machines, and when they replace the bearing it goes bad again shortly after.
      Has anyone come up with a solid fix for this? I've read it may be possible to run the UTV without the bearing at all, is that true? Are the $20 replacement bearings from eBay and Amazon complete garbage, and is there a better one way bearing out there that's built stronger? Is there something else causing this bearing to wear out faster, or is the stock bearing complete junk?
      Any input is appreciated, thanks in advance!
    • By Mark Anderhalt
      Question, Does anyone know if a 700-cylinder, piston, and head fit on top of a 500-bottom end, Although I have a 500 and have rebuilt the 500 once, I'm thinking the lower end may be the same for both the 500 and the 700. Does anyone have information on that?
    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Fishing Wiskers
      Top speed is 30mph on flat grass ground.  but it will not go up minor hills forward or reverse without a runing start.  If you start at the bottom of the hill machine will stop about 1/2 way up.  I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some.  Dosent matter if engine is cold or warmed up.  Seat belts are connected.  Fuel is clean
      I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch, 
      I am not sure how to check for codes with this machine,  can anyone teall me how to do it?
       
      Compression with hot eng is 145,  valves adjusted to .005 with a cold engine.  Dash shows 426 hours
      I am not convinced it's an engine problem
    • By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
×
×
  • Create New...