Quantcast
Jump to content


2013 UT 500 won't go into reverse.

lonerider98

By lonerider98
in Coleman UTV SxS Forum

 Share

Recommended Posts

lonerider98 Rookie

lonerider98

Posted
Posted

At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!

Ben1098 Enthusiast

Ben1098

Posted
Posted

Look up some of my old posts on shift issues.  The throw from the shifter end is "less than" the required travel to get F N and R.  Adjustment of the shift linkage will give

F and N....or.....N and R.  Look for the post on how to shorted by 1/8" by cuttiing the "bell crank" plate and rewelding  to make it shorter.  

Dale Stansbery Apprentice

Dale Stansbery

Posted
Posted

I imagine my 550 linkage is similar to your 500. I have to be sure my engine is at complete idle, and sometimes have to press hard on my brake to get it to shift into reverse. Now it may be the adjustment is a little off, but so far the above steps has allowed me to get it into reverse.

  • 2 weeks later...
aefron88 Community Regular

aefron88

Posted
Posted

Try playing with the adjustment. The 500/550's don't have the same shifter cable/lever issues as the 40's but the cable can stretch over time.

If you're getting grinding and popping out of gear it could be worn clutch dogs too, which require some effort to replace as they're internal to the transmission.

If you're having shift issues and grinding it's best to be proactive about adjusting because it does damage the dogs over time, and eventually will just pop out of gear at will once the dogs are rounded enough.

  • Like 1
  • 3 weeks later...
lonerider98 Rookie

lonerider98

Posted
  • Author
Posted
On 3/22/2024 at 11:41 AM, lonerider98 said:

At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!

So when push hard on the brake and I mean hard it will go into reverse. Is there a brake switch that could be going bad or Do you all think it's a adjustment fro the shift cable?

I haven't had a lot of time to really get into this. just picking brains right now. Thanks for any help!!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Bobbers
      Axis 500 parts
      By Bobbers
      My wife accidentally ran the Axis 500 into a fence and tore the front end up (broke her arm too). Just wondering where the best place to get front end parts? I know she busted the knuckle but haven’t jacked it up yet. Thanks guys for any help!
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Prepper
      2015 MSU-500 crank - no start
      By Prepper
      I'm working with a 2015 MSU-500.  Basic symptoms are it cranks well, but will not fire.  It has spark, and it has fuel spraying out of the injector (and spraying starting fluid into the throttle body and plug hole makes no difference).  It has compression.  I bought it not running, and no other information was available.  It has 775 miles on it and 127 hours.  It looks to be in very good shape.   Previous owner replaced fuel pump, ECU, coil, plug, and the fuse/relay box that mounts on the firewall, then gave up.
      My questions relate to cam/valve timing, considering the symptoms and diagnostics so far.  My thinking was the woodruff key sheared off and the crank spun, making it out of time.  My question is, by the pictures attached does anyone have an opinion as to the cam/valve timing being correct?  In the crankshaft picture you can see a timing mark visible.  In the camshaft picture I have arrows directed towards what I think are timing marks (which appear to be exactly 180 degrees from one another).  However, the long arrow in what appears to be bolt configuration in line with the piston/rod line.  Here is a puzzling note... in the position you see in the pictures... I have valve lash on both the intake and exhaust.  I think it's at TDC, given the visible crank timing mark and valve lash on both valves. 
      Any thoughts ?  Does this appear to be in proper valve time ?  Have I missed anything simple ?  Thanks in advance for your input.


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...