Quantcast
Jump to content


T-2 Rear Wheel Bearing


Randy

Recommended Posts

Hi,

I have been away from the forums for awhile, just enjoying my Trooper......

I have about 1500 miles on my '08 T2. I do not race, jump or otherwise beat it up except when it is put into extreme 'situations' (which I always manage to get into!) I have all the factory mods plus had a turbo installed by Scott at Unleashed in Cottonwood, AZ. It has been a terrific, bascially trouble-free vehicle so far.

On my last trip, (lake Pleasant to Crown King) the rear wheel lugnuts loosened up, I retightened and later on, the wheel actually wobbled completly off! I guess the bearing had gone and the wobble undid the lugnuts.

The issue is when I replaced my drivers side rear wheel bearing, the OEM replacement I was able to get from SilverBullet in Yuma just pushed right into the hub. I was expecting they would need to be pressed in. I am worried that perhaps the hub is 'worn' or otherwise part of the problem. I could not compare to the other side because I could not get the other axle nut off! Has anyone had some experience in this area they could pass along?

Thanks

Randy

Link to comment
Share on other sites

Guest Lenny

If the bearing fit in close enough, you could use loctite 272. Be sure to clean the surfaces good and slightly roughen with sandpaper. If the bore is too loose then you will need to have it slightly bored to clean it up and then have a thin sleeve made so everything presses together. If it's loose in there, it will get worse and you will end up replacing the bearing again and boring it anyway. When I replaced mine, I converted to tapered roller bearings. This required a lot of custom fitting but provides about 2-1/2 times the holding strength against side sliding forces which are the destructive forces causing the problem. The Joyner bearing is far too narrow to hold side forces. To get the nut off the other side, use a 3/4" socket drive with braker bar with a pipe. Hold the hub form turning by putting a bar between two lug bolts and to the ground. The nut can be very tight.

Lenny

Link to comment
Share on other sites

If I remember correctly, when I took mine off, the wheel does go on and off by hand, no pressing, but the axle nut needs a whole lot of torque, I borrowed some sockets from Checker Auto and 1/2 breaker bar and 5 feet of pipe to torque mine down, no problems yet, be sure to put the cotter pin in.

Kinarfi

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By hetovi
      Hey everyone,
      I’m in the market for a UTV windshield that can withstand extreme conditions, including high winds, dust, and off-road impacts.
      I’ve seen a lot of options out there, but I’m unsure which one will provide the best protection and durability.
      Does anyone have experience with windshields that excel in these environments? Are there specific brands or materials you recommend?
      I’m particularly interested in options that offer both durability and clarity.
      Any tips or personal experiences would be greatly appreciated!
    • By diamondjfarm
      I got an old 2003 Arctic Cat 375 Auto, and just bought a 2008 AC 650 side by side. Got a new starter, solenoid, and battery for the 650. Gonna change the crankcase oil and filter while I'm at it.
      Anything I oughta watch out for from them that's done the starter/solenoid on this model?
      Don't have a manual yet for the 650. Any recommendations for oil weight/grade?
      Thanks.
×
×
  • Create New...