Quantcast
Jump to content


Recommended Posts

Posted

Getting ready for the Jamboree and changing oils, Being lazy, I had to figure out and easy way to do it, So I pulled the vent hoses and cleaned them and then poured 1/2 quart into each diff through the vent tube. Took a while, but no mess what so ever. I split a quart diff oil between two bottles and tape them upside down to the frame and leave them over night. you do have to pull the fill plug for the air to vent and poke a hole in the bottle. Found very little metal on the magnet and the oil appeared relatively clean. Not like the silver paint from past oil changes. Also, when changing the oil filter, which always makes a mess, I found that if you place a plastic bag over it and poke a hole in the filter, and let it drain into the bag, no mess there either.

Jeff

Posted

I got the oils changed and no oil pressure, but then I didn't have a good reading before, sometimes it would just bounce hi to low and sometimes just pin on the high side. Any way, I'm pretty sure the sender is shot, so I need a new one, maybe a new gauge too. Any one have any suggestions? numbers? Prices? Been looking at the TeleFlex Morse Part # IA15001 0-80 psi, 240-33 ohm

Gauge -- TeleFlex Morse Part # 57903P 0-80 psi, 240-33 ohm as suggested by Zorro.

Thanks,

Kinarfi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Justine
      I've had a Hisun Vector E1 for just a bit longer than is required for me to do some maintenance. While it's well-overdue, it only drives 1.5km a few times each week on a fairly decent gravel road (to the letterbox), and it has worked really well right from the get-go.
      Looking at the manual it states that I need to use SAE80 API GL-4 Hypoid Gear Oil for the Main gear Case, and SAE80 API GL-5 Hypoid Gear Oil for the Front gear Case - unfortunately i can't find either of those online here in Australia. Plenty of options that look close, but, as someone who has never driven any vehicle before, I want to use the right thing and it's a tad confusing.
      My question: Since there are no oils that are bang on SAE80 (they all seem to cover a range) would Liqui Moly Hypoid GL4 Gear Oil 80W-90  & Motorex Hypoid GL-5 Gear Oil 80W90 - be ok to use? (Or any other suggestions of what I might be able to purchase online in Australia) And would I have to drain out any existing oil from both gear cases?
      This is a whole new world for me and  being able to find exactly what is specified in the manual hasn't made this easy!
    • By tskm
      in desperate need of a rear differential for my 2014 wildcat 1000. It has blown up right in the midst of the hurricane that struck us here in N/W N.C. I could really use this machine right now. No luck finding this from Artic Cat or the many numerous online vendors. Any info or resources wil be greatly appreciated !
      Tom 
    • By russnropes
      For the life of me I cannot find the directions on how to change the display to the standard for the USA - MPH. Not sure why Tractor Supply didn't do it before I bought it but it is what it is. Does anyone have the instructions to do this. I have the 2023 T Boss 550 just to be clear.
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
×
×
  • Create New...