Quantcast
Jump to content


Farmington buggy build

Jarrad

By Jarrad
in Joyner UTV SxS Forum

 Share

Recommended Posts

Jarrad Community Regular

Jarrad

Posted
Posted

We started the build for the farmington buggy yesterday making nice progress.. wheels are off to powdercoat, the cage is being shortened 4"'s chopped the lightbar installing mini Piaa lights, stereo, warn winch, tube fenders front and rear, rock sliders, I am using a 2008 T2 it's all we had left in stock 2 used buggies, but I went ahead and converted it from electrical 4X4 to namual lever

More photos to come!

Jarrad

DSCF0849.jpg

DSCF0848.jpg

DSCF0847.jpg

DSCF0846.jpg

DSCF0850.jpg

rocmoc Grand Master

rocmoc

Posted
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Tomorrow we get down to the nitty gritty, we were running short on the 1.5" .080 wall DOM tubing, have 100 feet being delivered in the morning, we start on the tube doors in the morning that will swing open.. this is going to be something unlike you guys have seen before.. we also still have to build the new spare tire holder and add the rock sliders.. The passenger grab handle is almost finished and I finally found the face for my stereo set up.. we are cruising along nicely..

The buggy will get wrapped first of next week and we expect the wheels to be back this friday so I can get it back in rolling condition so much work and hardly enough time to do it all.. will be pushing the deadline pretty close with the wrap job suppossed to tgake a few days

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

The rock sliders are being built right now, I pick the wheels up first thing in the morning, need to install the stereo and build the spare tire mount next, put my new G-force seatbelts in and a few minor details then hopefully tomorrow afternoon I can get it to the wrap shop

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

How much to bring a set of the door mounts & door tubes to Farmington? I am sirius!

rocmoc n AZ/Mexico

Actually wait till you see it finished.. And someone bring thier checckbook.. I don't really want to haul it back home

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

How much to bring a set of the door mounts & door tubes to Farmington? I am sirius!

rocmoc n AZ/Mexico

Nearing the end wheels here today mounted tires and my guy Aurturo is building the back half and tire carrier

DSCF0864.jpg

DSCF0861.jpg

DSCF0863.jpg

DSCF0862.jpg

DSCF0865.jpg

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

Finished except for the wrap

DSCF0869.jpg

DSCF0868.jpg

DSCF0867.jpg

DSCF0866.jpg

DSCF0870.jpg

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Looks real good.What did you use to mount the stereo ? was that a joyner item?

Thanks,

No it is something I whipped up quite awhile ago.. has been on 3 buggies, there are also rear speakers and a box but without the rear tire rack to mount them to I did not install

Guest Lenny

Guest Lenny

Posted
Posted

No it is something I whipped up quite awhile ago.. has been on 3 buggies, there are also rear speakers and a box but without the rear tire rack to mount them to I did not install

Nice job Jarred. Did you put the Renegade diff gears in it? Looking forward to Farmington.

Lenny

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Nice job Jarred. Did you put the Renegade diff gears in it? Looking forward to Farmington.

Lenny

I have not yet.. took it to wrap this morning, depends on how long they take, will be deciding factor on the gear set, I had the choice between a little better crawl ratio or looking good.. looking good took the better part of my judgement for right now

brostar Proficient

brostar

Posted
Posted

It sort of reminds me of an old 10cc Song

I was walkin' down the street

Concentratin' on truckin' right

I heard a dark voice beside of me

And I looked round in a state of fright

I saw four faces one mad

A brother from the gutter

They looked me up and down a bit

And turned to each other

I don't like Jarrad's Trooper

I love it

I don't like UTVs

I love them

Don't like Farmington,

I love her (New Mexico Holiday)

To every one going, have a bloody good time. I reckon that old 10cc song would sound pretty good blasting out of your new stereo set-up Jarrad.

Cheers Mike.

ricksrb Mentor

ricksrb

Posted
Posted

I have not yet.. took it to wrap this morning, depends on how long they take, will be deciding factor on the gear set, I had the choice between a little better crawl ratio or looking good.. looking good took the better part of my judgement for right now

Are you going to post some pics when you get it back from being wraped? anxious to see it.

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Are you going to post some pics when you get it back from being wraped? anxious to see it.

You bet I am I can't wait for tomorrow, not sure what time it will be though.. I need to call them and ask that question.. Still unsure it will fit in my enclosed trailer, may have to haul it on the flat-bed

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Are you going to post some pics when you get it back from being wraped? anxious to see it.

They are telling me late tomorrow afternoon, But here is the last trooper they did for me so use your imagination on what it will look like, I am getting the same black and real flame job

2009 Joyner Trooper

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • camojay
      Hisun Sector 450 (2021) - help diagnose rear diff issue (short video included)
      By camojay
      When we first heard the noise, we immediately stopped driving it...at first we thought it might be a linkage issue, but after further inspection looks like the sound/jolting is coming from the rear diff. Took a video below...
      Anyone know what is creating the diff to skip/jump like this? We drained the diff oil and didn't look terrible, no metal.
      Other info that may be useful:
      1400 miles on it
      Recently tightened the E brake
      P.s. never posted on this forum before, let me know if the video does not work
      20240817_133539_1.mp4    
    • Robbie Wyre
      2005 Cub Cadet side by side front axles
      By Robbie Wyre
      I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles.  I have a slide hammer puller on the inner joint and with all my strength they will not budge.   Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out?   Any suggestions please and thank you.
    • GaryC
      Need Rear Diff for Arctic Cat 1000X UTV
      By GaryC
      Unfortunately my rear Diff housing cracked on my 2013 and I need to replace it or find a good used complete differential.  I think the same one was used from 2013-2016?  Any help or referrals appreciated.  Thanks, Gary  (949)370-2575 (in UT)
    • lowgear52
      rear differential /Alibaba???
      By lowgear52
      Has anyone purchased a rear differential from Alibaba, they want $432.00 for diff and $35.00 for shipping. This would be a great deal if I can trust them any thoughts?
    • KimAC
      Front Shocks for Landpride Treker 4200NT
      By KimAC
      I need a pair of front shocks for a Landpride Treker 4200NT, from 2005?  Does anyone know of a good salvage yard - or another source?
      The old shocks have "SEBAC 11685 12 3" stamped on them (or something very close - it's hard to read). I think SEBAC are (were?) an Italian company.
      Is there a compatible shock I can use? I don't have easy access to a scrap yard where I can compare shocks etc.
      Thanks,
      -Kim

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...