Quantcast
Jump to content


Farmington buggy build

Jarrad

By Jarrad
in Joyner UTV SxS Forum

 Share

Recommended Posts

Jarrad Community Regular

Jarrad

Posted
Posted

We started the build for the farmington buggy yesterday making nice progress.. wheels are off to powdercoat, the cage is being shortened 4"'s chopped the lightbar installing mini Piaa lights, stereo, warn winch, tube fenders front and rear, rock sliders, I am using a 2008 T2 it's all we had left in stock 2 used buggies, but I went ahead and converted it from electrical 4X4 to namual lever

More photos to come!

Jarrad

DSCF0849.jpg

DSCF0848.jpg

DSCF0847.jpg

DSCF0846.jpg

DSCF0850.jpg

rocmoc Grand Master

rocmoc

Posted
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Tomorrow we get down to the nitty gritty, we were running short on the 1.5" .080 wall DOM tubing, have 100 feet being delivered in the morning, we start on the tube doors in the morning that will swing open.. this is going to be something unlike you guys have seen before.. we also still have to build the new spare tire holder and add the rock sliders.. The passenger grab handle is almost finished and I finally found the face for my stereo set up.. we are cruising along nicely..

The buggy will get wrapped first of next week and we expect the wheels to be back this friday so I can get it back in rolling condition so much work and hardly enough time to do it all.. will be pushing the deadline pretty close with the wrap job suppossed to tgake a few days

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

The rock sliders are being built right now, I pick the wheels up first thing in the morning, need to install the stereo and build the spare tire mount next, put my new G-force seatbelts in and a few minor details then hopefully tomorrow afternoon I can get it to the wrap shop

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

How much to bring a set of the door mounts & door tubes to Farmington? I am sirius!

rocmoc n AZ/Mexico

Actually wait till you see it finished.. And someone bring thier checckbook.. I don't really want to haul it back home

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

How much to bring a set of the door mounts & door tubes to Farmington? I am sirius!

rocmoc n AZ/Mexico

Nearing the end wheels here today mounted tires and my guy Aurturo is building the back half and tire carrier

DSCF0864.jpg

DSCF0861.jpg

DSCF0863.jpg

DSCF0862.jpg

DSCF0865.jpg

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

Finished except for the wrap

DSCF0869.jpg

DSCF0868.jpg

DSCF0867.jpg

DSCF0866.jpg

DSCF0870.jpg

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Looks real good.What did you use to mount the stereo ? was that a joyner item?

Thanks,

No it is something I whipped up quite awhile ago.. has been on 3 buggies, there are also rear speakers and a box but without the rear tire rack to mount them to I did not install

Guest Lenny

Guest Lenny

Posted
Posted

No it is something I whipped up quite awhile ago.. has been on 3 buggies, there are also rear speakers and a box but without the rear tire rack to mount them to I did not install

Nice job Jarred. Did you put the Renegade diff gears in it? Looking forward to Farmington.

Lenny

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Nice job Jarred. Did you put the Renegade diff gears in it? Looking forward to Farmington.

Lenny

I have not yet.. took it to wrap this morning, depends on how long they take, will be deciding factor on the gear set, I had the choice between a little better crawl ratio or looking good.. looking good took the better part of my judgement for right now

brostar Proficient

brostar

Posted
Posted

It sort of reminds me of an old 10cc Song

I was walkin' down the street

Concentratin' on truckin' right

I heard a dark voice beside of me

And I looked round in a state of fright

I saw four faces one mad

A brother from the gutter

They looked me up and down a bit

And turned to each other

I don't like Jarrad's Trooper

I love it

I don't like UTVs

I love them

Don't like Farmington,

I love her (New Mexico Holiday)

To every one going, have a bloody good time. I reckon that old 10cc song would sound pretty good blasting out of your new stereo set-up Jarrad.

Cheers Mike.

ricksrb Mentor

ricksrb

Posted
Posted

I have not yet.. took it to wrap this morning, depends on how long they take, will be deciding factor on the gear set, I had the choice between a little better crawl ratio or looking good.. looking good took the better part of my judgement for right now

Are you going to post some pics when you get it back from being wraped? anxious to see it.

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Are you going to post some pics when you get it back from being wraped? anxious to see it.

You bet I am I can't wait for tomorrow, not sure what time it will be though.. I need to call them and ask that question.. Still unsure it will fit in my enclosed trailer, may have to haul it on the flat-bed

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Are you going to post some pics when you get it back from being wraped? anxious to see it.

They are telling me late tomorrow afternoon, But here is the last trooper they did for me so use your imagination on what it will look like, I am getting the same black and real flame job

2009 Joyner Trooper

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • KimAC
      Front Shocks for Landpride Treker 4200NT
      By KimAC
      I need a pair of front shocks for a Landpride Treker 4200NT, from 2005?  Does anyone know of a good salvage yard - or another source?
      The old shocks have "SEBAC 11685 12 3" stamped on them (or something very close - it's hard to read). I think SEBAC are (were?) an Italian company.
      Is there a compatible shock I can use? I don't have easy access to a scrap yard where I can compare shocks etc.
      Thanks,
      -Kim
    • Eagle Mountain Outfitters
      NEW Rear Foldable Cargo Basket designed specifically for the Mule
      By Eagle Mountain Outfitters
      Our R&D team just finished the first unit and wanted to show you guys. Need more cargo space without losing the functionality of being able to fold down the seat to use the full bed? Eagle Mountain Outfitters, the maker of the original metal UTV roof, has designed a foldable rear cargo basket to meet your needs. Price is $625 + $30 shipping.  If you have any question's, please reach out to me at [email protected]
       

    • tskm
      2014 Artic cat “wildcat” 1000 rear diff
      By tskm
      in desperate need of a rear differential for my 2014 wildcat 1000. It has blown up right in the midst of the hurricane that struck us here in N/W N.C. I could really use this machine right now. No luck finding this from Artic Cat or the many numerous online vendors. Any info or resources wil be greatly appreciated !
      Tom 
    • Alien10
      Coleman 550 - Added Lights
      By Alien10
      I added lights to the Coleman Outfitter 550 last fall.   I bought lights on line from Nilight, a 300 W  12" light bar mounted forward and 2 square 4" floods for the rear.  Those are mounted on the roof corners facing rear and downward just beyond the tailgate.  Nilights seem to be of high quality, as I've had them on my garden tractor for 5 years and still flood the way ahead with great light. 
      Both the front and rear lights provide amazing illumination making the OEM headlamps look like parking lights.  Made a connector for the front bar that plugs into existing headlamp switch so it is just part of that circuit controlled by the headlamp switch.   Rear work lamps were wired in using a rocker switch installed in the dash.  Backed up to the garden with the work lights and was able to harvest some tomatoes well past sunset. 
      What have you used if anything for auxiliary lighting on your UTV?
       
       
    • jimvmcgee
      back up lights
      By jimvmcgee
      I have a 2023 560 T Boss that I just noticed that back up lights not working, the camera come's on. The book tells you about tail light replacement, so was wondering if the lens is just there.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...