Guest Lenny Posted August 5, 2010 Share #1 Posted August 5, 2010 x Quote Link to comment Share on other sites More sharing options...
rocmoc Posted August 5, 2010 Share #2 Posted August 5, 2010 Lenny, would it be better to replace with some good quality helm joints? rocmoc n AZ/Baja Quote Link to comment Share on other sites More sharing options...
Guest Lenny Posted August 5, 2010 Share #3 Posted August 5, 2010 Lenny, would it be better to replace with some good quality helm joints? rocmoc n AZ/Baja These heims joints are not that bad. They are actually pretty good. They have a good outside housing and a bronze bushing. The only problem is that they probably didn't have good quality control on pressing the bronze bushing when made leaving some of them not real tight. However if they were replaced with larger ones that would be better but this is free and it works. Lenny Quote Link to comment Share on other sites More sharing options...
mlg Posted August 5, 2010 Share #4 Posted August 5, 2010 Awsome going to do mine this weekend Quote Link to comment Share on other sites More sharing options...
bigdan120 Posted July 30, 2012 Share #5 Posted July 30, 2012 Mine was so tight that they sqeeked and was very annoying...So I pulled the Heims out turned the eye ball sideways and put some grease on them and wiggled the heck out of them...Go figure it rides so much nicer now......I also did the A arms bolt upgrade works out great with the 14mm bolb but I had too put the ball joint into place then run a Die grinder to cut the stem back alittle to get the bolt in...I did it on all 4 so i'm guessing it was not me...LOL I also did the Ball joint rubber replaemnet while I was there...Dormans fit perfect like someone else said that I can't find now....LOL Oh well...Hopefully take it out tonight for a while to climb the hill that kept kicking my ass a few weeks ago! Quote Link to comment Share on other sites More sharing options...
bigdan120 Posted July 31, 2012 Share #6 Posted July 31, 2012 UPDATE: Next day back SQUEEKING AHHHHHHHHHHHHHHHHHH....Not as bad but it's there....I WILL GET IT RESOLVED! Quote Link to comment Share on other sites More sharing options...
Kinarfi Posted August 1, 2012 Share #7 Posted August 1, 2012 In one of Lenny's earlier posts, he packed the Heim with grease and wrapped it with pipe insulation, when I get done with my current project, I plan to try Lenny's heim tightening trick and then pack it and wrap it. Quote Link to comment Share on other sites More sharing options...
bruhaw Posted August 1, 2012 Share #8 Posted August 1, 2012 http://www.vxb.com/page/bearings/CTGY/HR I replaced all of my heims joints including the tie rod ones which are smaller and use a needle style zert fitting. All of the other heims joints have the regular standard zert fitting. Mine were squeaking all the time and once I replaced them all - no more squeaking and I can grease after every outing if need be. I tried the rubber boot covers but they kept binding up and tearing so I don't and can't use them. Lenny was able to get them to work on his and I got the idea from him at the jamboree but no luck on mine. Either way they do get dirtier now but I can wipe off and just grease again. See link above. The ones we use are all right hand thread and16mm for all the larger ones and 12mm for the tie rods. POS16 and POS12 are the part numbers. Not too expensive either and well worth getting rid of that damn squeaking! 1 Quote Link to comment Share on other sites More sharing options...
Guest Lenny Posted August 1, 2012 Share #9 Posted August 1, 2012 The boots are nice if you can get them to work ok. I did a little extra maching to help mine work. Initially I covered them with pipe insulation which actually worked quite well in sheilding the joints while keeping the greese in so they stayed lubercated. That is what Kinarfi is going to do as he stated above. If you have greese fittings, the main thing is to be sure to regularly greese the joints to drive out any dirt that is trying to work itself in. With a quality joint, greesing them should make them out live the Trooper. I've heard of 12,000km to 13,000km so the next stop is 20,000km. That should be no problem. Lenny Quote Link to comment Share on other sites More sharing options...
bigdan120 Posted August 1, 2012 Share #10 Posted August 1, 2012 Thank You! That is the info I needed.........Hey how are you doing the install? Are you cutting off where ours are welded and threading the insides? Quote Link to comment Share on other sites More sharing options...
Guest Lenny Posted August 1, 2012 Share #11 Posted August 1, 2012 Thank You! That is the info I needed.........Hey how are you doing the install? Are you cutting off where ours are welded and threading the insides? Read this post. http://www.utvboard.com/topic/2351-replacing-a-arm-heims-joints/page__hl__%2Bheims+%2Bjoints__fromsearch__1 This what I ended up doing to mine. I consider this a final solution but it does take extra effort. Lenny Quote Link to comment Share on other sites More sharing options...
bruhaw Posted August 1, 2012 Share #12 Posted August 1, 2012 They are threaded inside the tubing and all I did was remove and install the new ones. No welding on my end. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.