Quantcast
Jump to content


2010 500 - New Carb- Hesitation

Buddee
 Share

Recommended Posts

Buddee Newbie

Buddee

Posted
Posted

Put a new carb on the 500 to replace the leaking OE one.  Machine idles fine and mid and top end runs great.  It tends to have a hesitation right from the start - bottom end.   Thinking it may be the air/fuel screw??  I didn't do anything with the carb out of the box and is it direct replacement for my machine.  Of interest is the manual choke doesn't seem to work very good now.... wonder is it getting too much air?

 

Any help appreciated!

 

 

  • 2 weeks later...
Buddee Newbie

Buddee

Posted
  • Author
Posted

Just going to follow-up on this one.  I turned the fuel/air screw out 1/4 a turn (counterclockwise) and the hesitation is all but gone.  Might do another 1/4 turn rid it completely.  She needed more fuel.

 

 

LongSun Apprentice

LongSun

Posted
Posted

It sounds to me that the acceleration nozzle (or pump) needs to be adjusted. 

The thing runs great at idle and mid and top range. It only needs more fuel when you open the throttle.

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Frank in MI
      New old guy
      By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • Poppateets
      New owner with questions
      By Poppateets
      I just purchased a used 2023 Massimo warrior UTV SxS 1000mx with 600 miles on it. I didn't even get a full day of riding and the driver's side rear axle broke. I'm pretty sure it was already going bad because we would hear a noise once in a while. I'm wondering if anyone else has had problems with theirs. Also looking for places to buy accessories.
    • NC4wd
      Axis 500 Lift Kit
      By NC4wd
      Has anyone found a lift kit that fits an Axis 500? Mine is a 2021.
    • Jacob E freeman
      2018 cub cadet challenger 750 over heats no one knows why
      By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • Will Sutton
      Coleman UT400 won't rev. Idles fine
      By Will Sutton
      I've got a 2023 UT400 (bought from tractor supply) and I've been beating my head against a wall with it.
      It will start and idle perfectly. The second I touch the throttle it sputters and dies.
      I've checked that the fuel pump is working  (it is).
      I've replaced the injector, throttle position sensor, O2 sensor, and intake air sensor. All with no change.
       
      I've just taken a look a the schematic, and there is a crank position sensor as well.

      Could this be the source of my troubles? If so, where is this thing located? I can't seem to find it on any drawings from the parts suppliers.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...