Quantcast
Jump to content


Braking Systems - A dedicated Thread


rocmoc

Recommended Posts

My e-brake has never work correctly so I am turning them into turning brakes like I had on my dune buggies. For a e-brake I am going to install a micro-lock.

rocmoc n AZ/Baja

My e-brake worked excellently in the beginning and would hold me on hills while I got the engine revved up and the clutch engaged and is something my injuries require me to have.

The Mico-Lock system would be nice be expensive, http://www.tsmmfg.com/mico_hydraulic_brake_lock.htm I've driven trucks with the Mico system and liked it, but looks like too much work and money for me, but still a good idea.

Then there is Lenny's set up, I'll let him detail that.

Kinarfi.

Link to comment
Share on other sites

My e-brake worked excellently in the beginning and would hold me on hills while I got the engine revved up and the clutch engaged and is something my injuries require me to have.

The Mico-Lock system would be nice be expensive, http://www.tsmmfg.com/mico_hydraulic_brake_lock.htm I've driven trucks with the Mico system and liked it, but looks like too much work and money for me, but still a good idea.

Then there is Lenny's set up, I'll let him detail that.

Kinarfi.

I could see using two micro-locks, one for each back side and hook it up to work with both brakes on each side. Hook the 2 brakes together off the one line like I did on each side. Set up the steering handles so you can pull the right or left for turning or both at the same time for an e-brake. Then when you use your foot brake you would have double the stoping power on each side. It's not that hard to put another set of calipers on the front either. If your in 4x4, then your e-brake would hold all four wheels. If you remember, I have 2 calipers on each wheel for regular foot braking and my e-brake is now a disc on the front drive shaft like they used to do years ago. It's nice having brakes that I don't have to bear down on to stop on a steep hill. Having the e-brake on the drive shaft is nice because it goes through the differentials which give a 2.15:1 power increase making it possible to lock up all four wheels and skid to a stop on gravel. For you Kinarfi, I could see using an old parking brake, the ones that use to stick out below the dash with a T-handle. They used a cable which you could tie into the regular brake pedal to give you 3 ways to apply the brakes. By foot or pulling up with the handle turned so it doesn't stay up for use on hills while holding clutch and just pulled up for parking. Should be easy to find in a junk yard.

Lenny

Link to comment
Share on other sites

Guess I shouldn't been surprised, House Of Hose wouldn't fix my brake line, flat refused even though they could have, "LIABILITY" and for them to build a new one was $75.00 so I looked at http://www.jmcmotors.us/my_account.php and it was only $29.21, brake pads were $11.40, per set I hope, ORDERED!!

Now to build some sort of visual, audio alarm for when I leave the brake on.

Kinarfi

My e-brake worked excellently in the beginning and would hold me on hills while I got the engine revved up and the clutch engaged and is something my injuries require me to have.

Kinarfi.

Well I got my brake line in from JMC and got it installed with a new set of shoes and now it seems to doing it job again. Not sure how others bleed their brake systems, but when I had my airplane and bought brakes for it, they came with Plews oil can and some polyurethane tubing and you pumped fluid into the brake until it came out the master cylinder, it worked good because it was all uphill.

Found that can and cleaned it out and made a cap for the reservoir with gasket and put a fitting in the top and started pumping fluid with the oil can until it came out the brakes and it was as solid as it could be, no sponginess!!! The only thing better that I know of would be a brake bleeder pot. I remember pumping brakes until it got firm, someone else would bleed until the peddle hit floor, close the bleeder, pump, bleed, close, pump, bleed, close,........ until solid. Definitely took two people. This was doable solo and worked great and easily.

Kinarfi

Link to comment
Share on other sites

Here's an idea for someone with machining abilities, no names, but if you take a set of calipers and machine a threaded lever into the back of the caliper that is attached to lever. you have your independent left or right braking set up. You'd need a right hand thread on the left and a left hand thread on the right.

Kinarfi

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Greg Kilgore
      This started back in the summer. 
      While on a ride with the wife. Applied the foot brake and the pedal went to the floor. Thought the brake pads were gone. Ordered new pads. Removed the wheels to install new pads and they were in good shape.
      So I bled all 4 brakes cylinders. Got thin dirty fluid out. Almost like dirty water. No air. Got a good pedal.
      Then about a month later, same thing, brake pedal back on the floor. Could pump the pedal and get a little pedal back. Bled again and finally got a good pedal. The fluid was nasty like before. No air. And the fluid was topped off in the reservoir before I started the bleeding process.
      Now same thing. Pedal going back to the floor. Reservoir still full. I'm thinking the master cylinder is bypassing. So have a new on on the way and will report back.
      What do you guys think. Could it be something else.
      I used one of those hand operated vacuum pumps to pull the fluid out of the reservoir when I was bleeding before. First time I've used one. And after a small amount of fluid filled the catch bottle. Seemed like the vacuum pump quit working. Had to close the bleed screw. Pump the brake one time. The start the vacuum thing again.
      Again just wondering what you guys think. Using DOT 3 and DOT 4 brake fluid. Whatever I can get at a reasonable price at parts store.
       

    • By Fishing Wiskers
      Top speed is 30mph on flat grass ground.  but it will not go up minor hills forward or reverse without a runing start.  If you start at the bottom of the hill machine will stop about 1/2 way up.  I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some.  Dosent matter if engine is cold or warmed up.  Seat belts are connected.  Fuel is clean
      I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch, 
      I am not sure how to check for codes with this machine,  can anyone teall me how to do it?
       
      Compression with hot eng is 145,  valves adjusted to .005 with a cold engine.  Dash shows 426 hours
      I am not convinced it's an engine problem
    • By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
    • By FGT
      QUESTION: How to wire the C/B into this current dual battery set up.

      EXISTING SITUATION: MAIN Battery is OEM and feeds OEM circuits. Added an AUX Battery in the OEM dual battery location. Connected the AUX - terminal to the MAIN - terminal. Connected the 100A Accessory Fuse Block power cable to the AUX + terminal. Installed a smart isolator between AUX and MAIN batteries where a cable from AUX + goes to the isolator and a cable from isolator to MAIN battery + terminal. Installed separate QD battery tender cables to both AUX and MAIN batteries + and -. The dual battery system appears to work as intended. For this Phase 1 improvement, to avoid having to constantly pull the leads on the AUX + battery post off and put on, for testing or maintenance of Accessory circuits, I wanted a more convenient and safer way to open the circuit from the AUX battery + terminal the Accessory Fuse Block. I called an off road dealership and was told to install a much larger capacity circuit breaker than the 100A rated Fuse Block and was recommended to get a 250A C/B like the one in the pic, which I did. I was told the reason for the C/B high amp rating was two-fold (a) to trip in the event of a battery short circuit and (b) to be able to conveniently open the C/B to kill power to the Accessory Fuse Block without removing leads from the AUX + terminal. The 250A C/B has two posts labelled "BAT LOAD" and "BAT LINE". There are currently three connections to the AUX + post: (1) Accessory Fuse Block power cable, (2) cable to Isolator AUX in terminal, (3) cable from AUX battery charger.


×
×
  • Create New...