Quantcast
Jump to content


Unusual timing problem


Recommended Posts

Posted

Trooper started running real poor. Would run real rich until I gave it gas then it would flood indicated by the oxygen sensor jumping to very lean, 20:1. When it floods, it stops burning the fuel so the oxygen is left over, but not because it is lean. Wouldn't hardly go. could idle but had no power what so ever. Figured I messed up my tune so played with it for a few days. I could get it to rum better but never good. Then I thought I damaged the engine so I checked compression, All 4 cylinders were at 135+-1 pound, not a problem. Remember I have lowered my compression for the supercharger so this was just right. Surprised they were so identical. Then rechecked timing with a light, perfect. Checked for input from all the sensors, no problem. Pulled the head cover to check if the timing belt slipped a cog, nope. Made sure all the valves had the proper clearance, fine. Checked my fuel pump for proper pressure and volume, OK. Scratched my head a lot and went back and read the Megasquirt manuals for about the 10th time. Then I went back to square one and set number 1 cylinder to top dead center to start over rechecking valve position and timing. Now timing showed being off by 30 degrees advanced. But the timing light showed it right on. Then it dawned on me, the 36-1 Edis timing wheel has moved. But how, it's weld on to the supercharger drive pulley which is tightly pressed onto the alternator stock drive pully. The stock drive pulley is the engines harmonic balancer so it has a rubber cushion molded in between the inner part connected to the crank and the outer drive pulley part. The outer portion was slowly slipping on the inner part gradually changing my timing but because the timing, the computer sees, is based on the placement of the missing tooth, it showed and checked correct. I omitted the rubber and welded it solid in the correct relationship to the engine and it all runs great now. That took about a week and was hard to find but finally it’s corrected.

Lenny

Posted

Did you take any photos, is the 36-1 Edis timing wheel the wheel that drives the alternator and water pump or is it something to do with your super charger and something the rest of us don't need to worry about.

Is it in this picture? Possibly, is it on the left side? 2943355750104110397ldGieM_th.jpg What timing is it effecting, spark timing, or injection timing and where is the timing signal coming from? I'm assuming the MegSquirt has it's own timing signal coming from the 36-1 Edis timing wheel. I'll ask more later.

Kinarfi

Posted

Did you take any photos, is the 36-1 Edis timing wheel the wheel that drives the alternator and water pump or is it something to do with your super charger and something the rest of us don't need to worry about.

Is it in this picture? Possibly, is it on the left side? 2943355750104110397ldGieM_th.jpg What timing is it effecting, spark timing, or injection timing and where is the timing signal coming from? I'm assuming the MegSquirt has it's own timing signal coming from the 36-1 Edis timing wheel. I'll ask more later.

Kinarfi

It's nothing you guys need to worry about. I mention it only because you can sort of see the process I went through to find a problem. The Edis 36-1 timing wheel is something I added to provide a timing signal for the megasquirt. What caused the problem has got to be about as rare as it gets. Sorry Rocmoc, don't use a lot of RPMs anymore, but I still wondered for a while if I damaged my engine. I have my RPM limit set at 5500 in the computer. Torque is good.

Lenny

Posted

It's nothing you guys need to worry about. I mention it only because you can sort of see the process I went through to find a problem. The Edis 36-1 timing wheel is something I added to provide a timing signal for the megasquirt. What caused the problem has got to be about as rare as it gets. Sorry Rocmoc, don't use a lot of RPMs anymore, but I still wondered for a while if I damaged my engine. I have my RPM limit set at 5500 in the computer. Torque is good.

Lenny

What computer are you running?

Posted

What computer are you running?

MegasquirtIII with the MS3X board for sequential injection and sequential individual ignition control. Real happy with it and very versatile.

Lenny

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • By fishhouse3
      FOR SALE: 2021 CFMOTO ZForce 800 Trail with many extras and full warranty until 2027. Only 625 miles and 50 hours of use.
      In great condition, has a clean title and one adult owner. Has had all scheduled regular maintenance and has not been abused. Only used about six times on weekend trips to Hatfield-McCoy trails in WV.
      Under full CFMOTO Care bumper-to-bumper extended warranty until 8/2027 (paid $1,600). Full service and tune up just completed with new clutch, drive shaft, belt, rollers, etc (paid $1500). Plus it comes with over $3,500 in upgrades and accessories! Way too many included items to list here (see last pics for full details).
      This machine is ready to go and needs nothing - just hop in and hit the trails!  I have over $20k invested in this machine. Priced VERY fair to sell quick at less than half that!!!
      $9,999 WITHOUT warranty -OR- $10,999 WITH full extended warranty until 8/2027.
      Located in Chesterfield, VA 23832. Message me for more pics and info!





    • By Callie
      We have replaced the relay/fuse, water pump, fan & radiator cap. What are we missing? Fan still won't kick on.
×
×
  • Create New...