Quantcast
Jump to content


Recommended Posts

Posted

Has anyone seen this yet

I might have to sell my joyner for one of these

‎30 inch long shocks, 16-17 inch wheel travel stock. 1000cc 95+ hp engine. Trailing arm suspension. Built to out do the RZR XP directly.... And MSRP target is less than an XP. Will be released as a 2012 model late this summer.

  • 4 weeks later...
  • 2 months later...
Posted

And here's the predecessor to the Wildcat.....

Getting ready for the Vegas To Reno Race in August...

Class 19, 17 inches rear and 16 inches front travel with King Remote Res Shocks, 100hp, Summers Bros 300M Axles, 28 inch ITP BajaCross Tires, 226ft of 1.75X.095 Chromemoly.

IMG_0141.jpg

IMG_0134.jpg

IMG_0142.jpg

IMG_0137.jpg

IMG_0138.jpg

Posted

I saw the video a while back and they look pretty good to me. I still like the Joyner concept of a car engine over a Motorcycle engine, but you can just tell this Cat is going to be a top predator.

I know an Arctic Cat dealer you can trust, Arctic Cat of DFW. Their new website is http://dfwarcticcat.com/ & this is a division of some business you might of heard about before called No Limits Powersports.

Cheers Mike.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By JSwearer
      Does anyone have any suggestions for aftermarket shocks.  I have a T-Boss 550 and took it riding in some rough trails and the stock suspension was uncomfortably rough.
      Thanks
    • By KimAC
      I need a pair of front shocks for a Landpride Treker 4200NT, from 2005?  Does anyone know of a good salvage yard - or another source?
      The old shocks have "SEBAC 11685 12 3" stamped on them (or something very close - it's hard to read). I think SEBAC are (were?) an Italian company.
      Is there a compatible shock I can use? I don't have easy access to a scrap yard where I can compare shocks etc.
      Thanks,
      -Kim
    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
×
×
  • Create New...