Quantcast
Jump to content


Kinarfi's Trooper as of April,2011


Kinarfi

Recommended Posts

http://news.webshots.com/album/580071332eNSKGM

Here's 50 photos I took yesterday, I wrote on a lot of them as to why they might be worth noting(safety issues), and a few thing I think caused me so grief.

2272095060104282158FfIgQh_th.jpg #26 is my redesigned air/oil separator, when my rings went bad, I had a lot of blow by which carried the oil mist into my intake manifold and I had standing oil in it, so I flipped the manifold and I like it that way, and pushed enough of the mist out to the stock oil/air to over load the breather filter to where it dripped oil out side and down the side of the air/oil separator canister. The new one is made out of 2 2" white pvc caps, 1 2"X3" pipe nipple and 1 breather filter from Checker O'Rielly. I cut the rubber mount off the breather and epoxied to the inside of one of the caps(vent) after drilling and tapping, drilled and tapped the pipe(inlet) and the other cap(drain, welded a bolt for mounting, assembled with teflon tape and painted it black (now if I get oil dripping off the vent filter, it drips back into the system and the vent is on the intake side of the main air filter, plus I used clear tubing so I can see if anything is happening).(probably don't need it now that my rings are good again :blink: )

I added a small catch bottle between the valve cover and intake just in case. When I did my re-ringing, I plugged the big hole in the valve cover and the hole coming out of my oil pan, BIG MISTAKE!!!!, when you turn the engine off, any cylinders on the compression stroke bleed of the compression creating internal pressure, and in my case, pushed oil out the tube in the oil pan because it was the weakest closure. Not now though.

still working on this post.

Kinarfi

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
    • By Isaac
      I have a 2013 odes dominator when I get in it.  It ideals fine but when you give it gas it bogs and goes and bogs and won’t go passed 30 can anyone help me 
    • By mac66
      Apparently, these are Hisun or at least they use Hisun engines. I can't find much info on them online yet.  Ran across a used one with just 100 miles on it as a very reasonable price.  Just curious.
      Okay, more info...they are owned by Textron Corp who also owns Bell Helicopter, Cessna & Beechcraft aircraft, Ez-Go & Cushman and Arctic Cat and a bunch of other companies.
      So are thy cheap Chinese crap machines or are they good to go?
    • By Off Grid Refugee
      I have a yanmar longhorn 6 seater which I believe is having fuel delivery issues.  It will run off of starter fluid and will sometimes run on gas but will not idle.  Fuel pump is new and verified to put out 56 psi.  Injector is new, I'm reading 10.5 volts at the injector, gas is new.  The unit will run when the engine symbol is not present at the gauges.  Diagnostic port doesn't appear to be present, can't find it where yanmar says it should be.  Oil is full but old.  Any ideas what's going on here?  Is there a maintenance function that will shut this machine down if it has old oil?
×
×
  • Create New...