-
Similar Topics
-
By Gary T
I generally use my challenger for light duty misc. use, and for plowing. The one thing I dislike about this machine is the difficulty in shifting. I've had it the shop and they adjusted the shifting lever, but I still have issues. Some times it shifts ok, but the problem is it is hard to get it to move the lever from high to reverse or low to high or from any gear to the other. Seems I always have to accelerate a little to get it to engage to what gear I need it to go to. This is definitely not normal.
-
By didgeridoo
Hello, All! I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth. I haven't torn anything apart yet (to diagram), so I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
-
By Kingfish
The conversion took about 350lbs. off the vehicle. It never rode great, but now I feel every crack in the road. I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff. I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order. Does anyone have the data for the original spring compression rate? I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
-
By Ridge Runner
Hi
i have a 2019 Coleman 550 Outfitter. The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening. There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place. The screws enter from inside the bed body, and I can’t figure out how to access them. This is right by the tail light assemblies. I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in. Bottom line I’m making it worse.
coleman was no help. If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole. Any ideas?
thanks
Ridgerunner
-
By Fishing Wiskers
Top speed is 30mph on flat grass ground. but it will not go up minor hills forward or reverse without a runing start. If you start at the bottom of the hill machine will stop about 1/2 way up. I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some. Dosent matter if engine is cold or warmed up. Seat belts are connected. Fuel is clean
I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch,
I am not sure how to check for codes with this machine, can anyone teall me how to do it?
Compression with hot eng is 145, valves adjusted to .005 with a cold engine. Dash shows 426 hours
I am not convinced it's an engine problem
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.