Quantcast
Jump to content


Joyner hard enclouser T2 Black


Recommended Posts

  • 2 weeks later...

I don't support the deletions that occurred in this topic's post and future deletions are under discussions among the mods. Please be understanding while we review the topic of censorship. We need participation of ALL of our members so please be patient.

rocmoc n AZ

Link to comment
Share on other sites

Resolved! We are going to do fewer deletions, unless really bad name calling occurs, but may ask a poster to edit their post to be a little more tactful but still make the same point. If not we will edit the post to show how the point can be made but toned down. We want everyone's input, good & bad but in a civil manner. IMHO the earlier posts were fine but nearing the line. Thanks everyone!

EDIT---Kinarf I agree and supports this decision,

Kinarfi

Link to comment
Share on other sites

Resolved! We are going to do fewer deletions, unless really bad name calling occurs, but may ask a poster to edit their post to be a little more tactful but still make the same point. If not we will edit the post to show how the point can be made but toned down. We want everyone's input, good & bad but in a civil manner. IMHO the earlier posts were fine but nearing the line. Thanks everyone!

EDIT---Kinarf I agree and supports this decision,

Kinarfi

Great decision by both of you.keep up the good work.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner
    • By sxr951
      2015 massimo 700.. need cylinder bolt!  it some special cut from factory,, its a 125 thread but its like between 8 and 10 mm  dont know where to find any ideas? thx
    • By kgs
      Got a hisun sector 550 2019 that's got 5900 Miles on it, this year it started to getting hard to start in morning, once I get it started it works good the rest of the day. But to start it in the morning I got to hold the gas pedal to the floor and it will fire up. I replaced the fuel injector but didn't help it. So I just ordered a new air filter and 02 sensor and a maf sensor to put on it to see if this will fix it. Anyone else had this problem. I'm hoping the parts I ordered will fix it. I also bought a new battery to put in it also.
    • By BOYD
      I have a 2004 KUBOTA RTV 900 DIESEL and I need to replace both front cv axels.I have been online looking at them and there seems to be a lot of different manufactures to choose from. My question is who makes a good aftermarket set of cv axels for this KUBOTA. I have read horror stories of people buying the  cheap Chinese brand only to find out they don't fit or they don't last very long and fail again. I hate to have to spend over $200 a shaft to get OEM from KUBOTA when I'm sure there is a company out there who probably makes it for them or makes comparable to OEM. Thanks for your help.
×
×
  • Create New...