Quantcast
Jump to content


trans. fluid does it have to be gl 3

burntwire

By burntwire
in Joyner UTV SxS Forum

 Share

Recommended Posts

Kinarfi Veteran

Kinarfi

Posted
Posted

the book call for gl 3 gear oil for the transmission well i cant find a gl 3 gear oil.i have found gl 4 and gl 5 but no gl 3.do i have to have gl 3 or is gl 4 or 5 just as good?thanks for the help

use the same stuff you put in the differential---75-90

http://www.autozone.com/autozone/accessories/Valvoline-1-qt-75W-90-high-performance-gear-oil/_/N-25t1;jsessionid=CECE419B01CBE76544A3B46AE53875C9.diyprod3-b2c13?counter=1&itemIdentifier=373222_0_0_

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Gary Gallo
      2022 tracker 800sx help
      By Gary Gallo
      Just wondering if anyone has had problems with bed warping coming from the heat from the muffler.. If I ride more than 5 minutes my bed starts warping from the heat.. Does anyone have any recommendations on what wrap or shield I can get to prevent this before my bed starts cracking or the warping becomes permanent.. I only have about 50hrs on the UTV.. Basspro said they haven’t had this problem from anyone else.. Hard to believe..
    • JOSEPH LAMAR
      Please help me solve this
      By JOSEPH LAMAR
      I have a 2020 axis 500 and I have replaced the TPS twice and the whole throttle body assembly once and still have code 122. I can barely drive the thing. It bucks and surges like crazy
    • joynersfuntillitbreaks
      please help im new to joyner
      By joynersfuntillitbreaks
      so i just picked up a 2008 1100 trooper and iv ordered a few parts for it now and 99% of what i got fits perfect my issue now is my rear wheel hub is stripped out got a new cv and it fits great but i order 2 different hubs from 2 different places now and they are both wrong the spline opening is to small to fit the factory cv shaft and yes the shaft factory part #s are the same paid 250 for an original new replacement if anyone has anything that works to replace the original hub please point me in the right direction 
    • Clayton Walker
      Im New here but just got my Uforce Fitted for Hunting Season
      By Clayton Walker
    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...