Quantcast
Jump to content


Trooper T2 Fuel Tank Sensor


wrgenoa

Recommended Posts

Try Jegs or Summit Racing and replace with a good aftermarket universal unit. You will have to change the sending unit and dash gauge both. The Joyner units are crap.

rocmoc n AZ

Napa Auto Parts also has a replacement that is universal. I looked at one but have not ordered or replaced. Seems like it is a good unit. I believe it is a VDO unit. I actually have an extra complete stock sending unit but it is for the deeper fuel tank. I have the tank that is under the rear seat so this one is too long.

Link to comment
Share on other sites

Napa Auto Parts also has a replacement that is universal. I looked at one but have not ordered or replaced. Seems like it is a good unit. I believe it is a VDO unit. I actually have an extra complete stock sending unit but it is for the deeper fuel tank. I have the tank that is under the rear seat so this one is too long.

If it's one with a float on the end of a wire, You can cut and bend the wire to work in the range that you need. I used one out of a Dodge pickup that way and it worked great. Was able to use the same stock gauge.

Lenny

Link to comment
Share on other sites

If it's one with a float on the end of a wire, You can cut and bend the wire to work in the range that you need. I used one out of a Dodge pickup that way and it worked great. Was able to use the same stock gauge.

Lenny

The only thing you need to worry about are the ohms. Not sure what the stock gauge is but there is a range on the Napa one. And yes it can be adapted to fit any tank.

Link to comment
Share on other sites

The only thing you need to worry about are the ohms. Not sure what the stock gauge is but there is a range on the Napa one. And yes it can be adapted to fit any tank.

2523214430104282158mXeElu_th.jpgHere's the components in the sender, the switches are reed switches activated by a magnetic float. I've repaired a few of them for myself and other members. Replaced mine with a capacitive sender unit that I built and need to pull out and see why it's not working, in the mean time, I just make sure it's full at the beginning of each outing.

Link to comment
Share on other sites

  • 1 month later...

2523214430104282158mXeElu_th.jpgHere's the components in the sender, the switches are reed switches activated by a magnetic float. I've repaired a few of them for myself and other members. Replaced mine with a capacitive sender unit that I built and need to pull out and see why it's not working, in the mean time, I just make sure it's full at the beginning of each outing.

My capacitive gauge quit working so I went back to doing the way Joyner did sort of, instead of 4 reed switches, I used 10, now when the tank is full, the needle is on the white line, then 7/8, then 3/4 in the middle of the upper blue, then 5/8, then 1/2 on the middle white line, the 3/8, then 1/4 in the middle of the lower blue, then 1/8, the empty on the while line, the 1/2R in the middle of the red, then 0 on the bottom white line. The picture shows the old and the new.

Kinarfi

post-90-0-42971300-1316305279_thumb.jpg

Link to comment
Share on other sites

  • 2 weeks later...
  • 3 years later...

what year?

I think I still have my original sender of 5 or 6 reed switches, Or you could build one like mine. It has 14 reed switches and 16 LEDs, the 1st & 16th are always on 2 thru 4 are red, nearly empty, 5 thru 7 are yellow, less than half, and the last 6 are green, good to go. The brass tube is in the center of the tank and sealed so the circuit board & reed switches are dry. Down side is you have 15 wires running from gauge to sender.

post-90-0-92242400-1435676305_thumb.jpg

Link to comment
Share on other sites

Guys im new here and was just wanting some help with a Joyner trooper 2009 that recently stopped idling. it will crank and will run as long as you keep giving it the throttle, but if you let off it just dies. any suggestions?

any help will be appreciated

Thanks

cbockshiner

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!
    • By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
×
×
  • Create New...