Quantcast
Jump to content


Electrical Issues

DevilDog

By DevilDog
in Joyner UTV SxS Forum

 Share

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Kinarfi Veteran

Kinarfi

Posted
Posted

Key on ,I get nothing on any of those pins???

find that 2 amp fuse, or at least that's what the schematic says,

The key is in run, not just on, right?, are your gauges active.

My nest step before tearing wiring harnesses apart would be to pull every fuse and test it and reinsert it, undo the connector plugs under the computer (there's 2 of them) and inspect and reconnect, one the ip wiring connector and the other is the body wiring connector as shown on page 55 of the TR1100 -T2 -T4 manual 2008.pdf manual.

kinarfi

Link to comment
Share on other sites
Kinarfi Veteran

Kinarfi

Posted
Posted

Devildog,

I was looking through some of my drawings and found this, 2441466080104110397RTTmFT_th.jpg, go forward and backwards from this drawing and take a look at it and see if it helps, yours being a little older may it incorrect, but it does have the fuses numbered and the wire colors and it looks like there may be 3 fuses for the ecu, power, one for the normally open outputs and one for the normally closed outputs. It may be that some of this even came from the 2009 schematic.

Link to comment
Share on other sites
DevilDog Enthusiast

DevilDog

Posted
  • Author
Posted

Devildog,

I was looking through some of my drawings and found this, 2441466080104110397RTTmFT_th.jpg, go forward and backwards from this drawing and take a look at it and see if it helps, yours being a little older may it incorrect, but it does have the fuses numbered and the wire colors and it looks like there may be 3 fuses for the ecu, power, one for the normally open outputs and one for the normally closed outputs. It may be that some of this even came from the 2009 schematic.

Link to comment
Share on other sites
DevilDog Enthusiast

DevilDog

Posted
  • Author
Posted

Started pulling all wiring connections apart spraying cleaner and putting on dieelectric grease on and bam - One of the connector plugs going to the ECU was the problem, evrything works starts right up!!! Thanks for everyones help. Going for a short ride Sun ( not to far from the truck) see if its fixed.

Link to comment
Share on other sites
  • 2 months later...
darrylsm Newbie

darrylsm

Posted
Posted

I know this post is a tad old , but I bought an R2 because of electrical problems related to the fuse box behind the passenger seat near the ECU. I had to make my own relay/fusebox set up temporarily , but I have ordered one from rick @ silver bullet in the mean time. Heres what I have learned about the ECU harness and rear fuse box setup.

I cut the wiring , yes all of it. It was badly burnt and unrecognizable.

As far as the fuse box is concerned Basically there are 3 negative potential outputs , those are what turn on the fan , fuel pump , and main relay.

There are a couple of wires that are fused , and run to the ECU , one is on all the time , the other keyed.

The rest of the wires feed the gauges , the coil packs , and injectors , there could be some more , but the detail escapes me.

If your coil pack wiring has the proper + potential , as well as the injectors and computer. You can trick the computer in to starting and running. I bought 4 relays 50 amp from ebay , and a universal fuse box.

My renegade is running , and I do plan on repairing it properly when the harness/FB arrives , but I just thought id throw that out there , to let you know there is hope in making these engines run with the ECU. My first thought was to convert it to carb/distributor , but after a little wire tracing (very little thanks to the diagram) and loss of hope of conversion lol my renegade is back on the trails.

Link to comment
Share on other sites
Kinarfi Veteran

Kinarfi

Posted
Posted

I know this post is a tad old , but I bought an R2 because of electrical problems related to the fuse box behind the passenger seat near the ECU. I had to make my own relay/fusebox set up temporarily , but I have ordered one from rick @ silver bullet in the mean time. Heres what I have learned about the ECU harness and rear fuse box setup.

I cut the wiring , yes all of it. It was badly burnt and unrecognizable.

As far as the fuse box is concerned Basically there are 3 negative potential outputs , those are what turn on the fan , fuel pump , and main relay.

There are a couple of wires that are fused , and run to the ECU , one is on all the time , the other keyed.

The rest of the wires feed the gauges , the coil packs , and injectors , there could be some more , but the detail escapes me.

If your coil pack wiring has the proper + potential , as well as the injectors and computer. You can trick the computer in to starting and running. I bought 4 relays 50 amp from ebay , and a universal fuse box.

My renegade is running , and I do plan on repairing it properly when the harness/FB arrives , but I just thought id throw that out there , to let you know there is hope in making these engines run with the ECU. My first thought was to convert it to carb/distributor , but after a little wire tracing (very little thanks to the diagram) and loss of hope of conversion lol my renegade is back on the trails.

Take some fotos and send them to me and I'll add them to mine so they can be shared, especially if you find some new information and if you need help and I can give it, let me klnow.

One thing I did for powering up the fan and fuel pump was to replace the relays with high power FETs, NO moving contacts. I'll be looking at the main relay now that you have brought it to my attention. Died you say there is power to the ECU all the time or just to one of it's fuses. Did you download the Trooper wiring Diagram schematic in parts and pieces under manuals? Did a copy and paste of the PDF and created a drawing of the information 2486333090104282158CLzAXt_th.jpg

Kinarfi

Link to comment
Share on other sites
  • 2 months later...
iltrooper Rookie

iltrooper

Posted
Posted

I had a master switch problem. I store my T2 in a warehouse so when I was in there I would always start it and let it warm just to know all was well. For no reason one day it wouldn't start. It would roll over only. No spark or injector pulse, (checked with a GM noid) but dash cycled, fan cycled, lights and accessaries worked. Thinking ECM or at least crank trigger I towed it to my shop and started to check things. Why I did it I don't know, but I cycled the main kill switch and it started! Real RELIEF!

Link to comment
Share on other sites
  • 3 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Reynolds Rocket
      2017 Intimidator XD4 800 Check Engine
      By Reynolds Rocket
      I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 
    • Jim Kessell
      EH65 spitting fuel from breather hose into air filter.
      By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • lmarkie
      Bulldog BD700 Engine Swap
      By lmarkie
      I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
      Only problem is the exhaust exit is toward the back seat instead of out the back.
      Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
      Any thoughts?
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • redneckred
      2012 Bennche 700X Engine code
      By redneckred
      Can anyone tell me how to get the engine codes to display on a 2012 Bennche Bighorn 700X?  I played with the gauges once and lucked up on this but can't remember what I did.  Will the codes automatically display if there is a code or do you have to cycle through the display?


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...