Quantcast
Jump to content


Tail lights

Leadfoot

By Leadfoot
in Joyner UTV SxS Forum

 Share

Recommended Posts

Leadfoot Explorer

Leadfoot

Posted
Posted

Ok, My tail lights are cracked and broken and Just dont look good AT ALL, So, If anyone has any for sale that would be GREAT! OR, Any ideas on replacements or mods would be great aswell!

2scoops Proficient

2scoops

Posted
Posted

Ok, My tail lights are cracked and broken and Just dont look good AT ALL, So, If anyone has any for sale that would be GREAT! OR, Any ideas on replacements or mods would be great aswell!

I have the same problem. Have you checked with Silverbulletmotorsports? The 2009 tail lights are far & away better looking than the 2008's. I have been putting it off because I may cut the rear bumper off & do custom tail lights from something else.

Banjo Minnow Enthusiast

Banjo Minnow

Posted
Posted

I replaced mine with the standard oval type. Had to trim the thin metal mounts to make them fit, but the rubber mount they come with is all I needed to mount them. Then installed two small yellow LEDs for turn.

Kinarfi Veteran

Kinarfi

Posted
Posted

Go with the LED oval http://cgi.ebay.com/ebaymotors/Red-LED-Oval-Trailer-Truck-Stop-Turn-Brake-Tail-Lights-/400215073106?pt=Motors_Car_Truck_Parts_Accessories&hash=item5d2ead6152#ht_1497wt_1165 ----- or something like these http://www.ebay.com/sch/i.html?_nkw=led+oval+brake+light&_sacat=0&_odkw=led+brake+light&_osacat=0&_trksid=p3286.c0.m270.l1313 . And to lose the amber turn light, You'll need to build or have me build for you ($5.00) a circuit so when you use the turn signal and brakes at the same time, they both work. http://www.utvboard.com/topic/1977-turn-signal-switch-on-the-column/page__view__findpost__p__8018

BigDogDaddy Enthusiast

BigDogDaddy

Posted
Posted

I used these, they work great. I got little MC turn signals to replace the broken ones.

My link

I just got redof the hole thing.. Never liked the looks of stock lights and mount.. Cut off and started over with these light from Maxxima.. They have built in backup lights you just have to tie in the stop/turn together.. They have the cool factor too.. See the pics in my gallery..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • SouthernGypsy
      Help needed, Anyone recognize where this Internally Threaded Bolt belongs?
      By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • se3388
      Anyone else with a UT10X?
      By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • Clayton Walker
      Im New here but just got my Uforce Fitted for Hunting Season
      By Clayton Walker

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...