Quantcast
Jump to content


Joyner Trooper Suspension Tricks?

charlie

By charlie
in Joyner UTV SxS Forum

 Share

Recommended Posts

charlie Experienced

charlie

Posted
Posted

Hey guys any suspension tricks out there for the trooper, to make it a little more friendly at the higher speeds??? I know we have all talked about the steering issues but is there any tricks to getting that free play out of the wheels does that kit I have seen on ebay take care of it.. Oh ya Rocmoc I did put the 30" tires on my T2 you werent kidding gearing is way better now thanx for the info

2scoops Proficient

2scoops

Posted
Posted

The kit is the best option until we can find a better steering box. The kit works quite well. Check for loosness through the entire steering system (tierod ends, steering shaft, u-joints, wheel bearings etc). Once you get all the play out & add the steering kit it should drive quite nicely at speed.

charlie Experienced

charlie

Posted
  • Author
Posted

The kit is the best option until we can find a better steering box. The kit works quite well. Check for loosness through the entire steering system (tierod ends, steering shaft, u-joints, wheel bearings etc). Once you get all the play out & add the steering kit it should drive quite nicely at speed.

thanx Ill give it a shot

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Dennis
      bd 300 bulldog shifting issues
      By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • strike250
      Free Massimo Buck 400 service manual
      By strike250
      I have the factory service manual available for the Buck 400. Just send me a message with your email and I'll get it to you. Although there is no charge for this, it would be great if  you would visit my website where you could donate any amount to help do things like this with others who need it. Again, there is no charge for this manual, and no obligation to donate. But if you did, I would thank you for sure. Have fun on the trails. www.warriorsoffroad.com
       
      Matt

    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...