Quantcast
Jump to content


Recommended Posts

Posted

Ok looked into the turbo kit a bit.

china t25/28 turbo $189

obx fmu $79.99

second f/p $59.99

mis barbed fittings/shop supply

oil lines ,either a/n and braided lines or jic hyd hose and lines, BTW kit icomes with rubber

cold and hot side tubing , mandrel bends and time at bench with Tig

exhaust log, same as above, just price of shop supplys

What else am I missing ? Not like I could afford it but I like to hope and dream ,maybe plan for next year lol

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Paul L
      When I am driving at 30 to 40 mph on the highway, the display will change from H (high) to R (reverse).  It does not actually shift into reverse, it seems to shift into neutral and starts losing speed and the gas pedal has no effect.  After the rpm/speed drops for 5 seconds or so, it changes back to H and runs fine for another minute or so.  You have to try to drive it at less than 5000 rpm or so, to try and keep this from happening.  Any ideas on what the problem might be?  It only happens at the higher speeds.
    • By Homeowner A
      Have a Coleman UTV 400 that cranks, runs, drives well until it gets warm and is put under load.  Light throttle or full throttle it doesn't bog, but it will cut out mid throttle if you move the pedal quicker than it seems to like for example when you're getting ready to go up a hill, but if you immediately floor it, it will do just fine and not cut out.  It's random if and when it's going to do it, but is consistent in that it happens only when hot/full operating temperature.  I've replaced the injector twice, same with the spark plug and tried different heat ranges (NGK 7,8 and 8 iridium), replaced the fuel pump, adjusted the valves, checked air filter which is like new, changed the oil, replaced the fuel filter.  No check engine light.  I don't have a code reader for this.  Initially I thought it might have a head or head gasket issue as when I got it, the oil was over full, very runny like water milky and it was smoking.  I've changed the oil since then twice to clear and clean everything out, and it seems to be good.  Coolant stays the same level and so does oil with no changes in consistency or need for adding more. Had I think 7-9 miles when I got it and now has about 77.  What should I try or consider next?  
    • By Robbie Wyre
      I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles.  I have a slide hammer puller on the inner joint and with all my strength they will not budge.   Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out?   Any suggestions please and thank you.
    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Buck
      My father-in-laws 750 hisun will not change gears unless he completely turns the motor off then shifts.  I thought it might be a brake problem but he thought clutch.  He took it to a jackleg down the road and he basically charged him $300 and did not fix a thing.  Any ideas would be useful because he really can’t afford throwing money at it.
×
×
  • Create New...