Quantcast
Jump to content


injectors

lowgear

By lowgear
in Joyner UTV SxS Forum

 Share

Recommended Posts

MauyThai1 Enthusiast

MauyThai1

Posted
Posted

Yes I'm an't dead yet, soory I didn't see you message. I have the injectors I bought from Lenny, I was trying them but I guess I couldn't get the fuel pressue right because the engine would start with them in. If you are still intrested let me know I'll sell them for 80.00 although Lenny charged me 500.00. LOL

Link to comment
Share on other sites
Guest Lenny

Guest Lenny

Posted
Posted

Hey, your a cop. Your setting a bad example. :P Did you ever get yourt waste gate figured out. I still think that is where the problem is. I think it's allowinig you to get into an over boost problem.

Lenny

Link to comment
Share on other sites
Guest Lenny

Guest Lenny

Posted
Posted

Lenny I did get the over boost problem fixed with a boost regulator, now it stops at about 8 psi but it will still try to over heat if I run fast for a while. As for stting a bad example thats is the way we have to roll. LOL

Your over heating can be taken care of by going to a larger radiator or at least a larger fan. I use both. My fan came from Ebay and is a 3000 cfm unit which is a lot more air then stock. My trooper over heated easily when totally stock. Did fine unless I ran it a bit hard for a while, just like your getting. Some owners don't have heating problems and others do. Maybe it's the cleanlyness of the inside of the block casting. Some just may allow a more free flow of coolant. Also you may want to space your fan farther from the radiator itself. Their cowling extends close to the radiator and blocks the corners of the radiator from getting air flow. I also moved the radiator back up against the vertical frame bars and put the fan on the inside. You get a bit better cooling if you are pushing the air thru the radiator rather then sucking it thru.

Lenny

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Jon V
      reassemble Cub Cadet Challenger 700 - Crankshaft does not turn freely
      By Jon V
      Good afternoon. When the timing chain came off its lower gear (previous owner had over-tightened the tensioner), I ordered new parts.. chain, oil-pump chain, tensioner etc.. But now that it's time to put it back together, the main crankshaft makes a clang noise and stops when you turn it by hand. I want to solve this before assembling everything. The camshaft cover is off so that the valves aren't being activated. Should the transmission be in neutral to turn the crankshaft? The engine was running fine until the chain came off the lower gear. Then it would spin when the starter motor engaged so I assumed the crankshaft was spinning. Any advice is appreciated.
    • mac66
      Anyone have a Bad Boy Bandit?
      By mac66
      Apparently, these are Hisun or at least they use Hisun engines. I can't find much info on them online yet.  Ran across a used one with just 100 miles on it as a very reasonable price.  Just curious.
      Okay, more info...they are owned by Textron Corp who also owns Bell Helicopter, Cessna & Beechcraft aircraft, Ez-Go & Cushman and Arctic Cat and a bunch of other companies.
      So are thy cheap Chinese crap machines or are they good to go?
    • sxr951
      anyone ever have to beat your starter out with a hammer till it broke in half?.lol
      By sxr951
      corrosion had its oring neck area  jammed in.. and besides that had corrosion in the starter just shorted when ran direct jumper cable to the starter post power to it

    • Joe Breaux
      still going
      By Joe Breaux
      just an update on my MSU 500 . For all the misery it caused me the first 2 yrs, and the combination of some quality YAMAHA parts, it has now become a reliable ,useful UTV without the constant fear of having to push or tow it back from trails. I have not had a single issue pop up in a very long time.. FINALLY!....and as a side note, I just bought  a C FORCE 600 ATV to replace an old and well used  Honda that finally after 18 yrs gave up a rod bearing.  So far the new one has really impressed me .. I like the new Power Steering and  this CVT Auto Trans is new to me on an ATV .. I m used to constant shifting on my Hondas .  It also has something I have never seen. Its EBS  engine brake system, as soon as you let go of throttle, it engine brakes you to a stop rather quickly.. its great idea for the grandkids safety . Takes a little getting used to tho.. All in all, I like it. We shall see how durable it is after break-in.. I do "RIDE" them! .....and they honor their warrenty! and the dealer is 15 minutes away.. 
    • BernieG
      Help identifying some disconnected components on a Yard Sport YS400
      By BernieG
      I could really use some help identifying some disconnected components on a Yard Sport YS400. The first part is this pipe, which comes out of the exhaust port area or the cylinder. It looks like it had a piece of rubber hose on it, but the hose is gone, and I have no idea what it was previously connected to.

      The second item is this vacuum valve looking thing.  Again only one line is still attached.  What is it's function and what other lines should be connected to it?

      The last thing is this hose, which exits the side top of the fuel tank (not the fuel line hose) but is not connected to anything

       
      Any help the community could provide would be greatly appreciated.  This UTV belongs to a friend, and I am trying to help him get it running correctly for his kids.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...