Quantcast
Jump to content


Oil pressure in Sand Viper 1100

lobo98382

By lobo98382
in Joyner UTV SxS Forum

 Share

Recommended Posts

lobo98382 Rookie

lobo98382

Posted
Posted

I ran my Sand Viper 1100 about 70 miles a few days ago with no problems. Today I washed the vehicle including the engine. After about 30 milutes I started it with no problems but the oil light was on very dim. The engine started to knock and I turned it off immediately. I checked the oil and it was only 1 quart low. I added oil and restarted it 3 more times with the same result. On the 4th try I let it run a few seconds and the knocking went away and the oil light went out. I use Mobil1 oil so the viscosity should always be the same. Does this sound like the beginning of an oil pump problem. I know in colder climates thick oil will take longer to circulate through the engine and some knocking noise is common, but this is not my problem. I'm just looking for suggestion. Thanks

Guest Lenny

Guest Lenny

Posted
Posted

I'd put an oil pressure gauge on it for starters. One quart low for an engine that only holds 3 and some quarts is more then I'd like to see.

Lenny

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Aaron Colona
      2022 t-boss 760 oil filter
      By Aaron Colona
      Just bought a brand new 760 about a month ago. I'm at 20 hours which the book says is when you need to change the break in oil. 
       
      I must be crazy, but I can't find the oil filter. I've googled a million videos...everything seems to be 2019 or lower...and/or a 550.  They all show the filter easily seen by looking in past the rear passenger tire on the engine. There is absolutely nothing there on mine. 
       
      1.there seems to be very little info if you Google a 760, or anything Massimo newer than like 2019. 
       
      2. Does anyone have a current model year 760 that can answer my riddle for me? 
    • Chile
      MSU 700 Oil Burning
      By Chile
      2018 Massimo 700 MSU. The machine started burning oil all of a sudden. One day fine-- next morning burning oil. Looking for advice. Do I pull the engine to inspect the top end or can it be done with the engine in place? Pro? Cons?
      Any and all assistance is greatly appreciated in advance.
      Chile
       
    • Prepper
      Which is the best oil to use ?
      By Prepper
      I have been doing a little research on which engine oil is best for UTV engines.  There seems to be some disagreement over using a good quality regular engine oil, and the necessity of using "M2" (or wet clutch suitable) oil.  My understanding is the "wet clutch" suitable oil has less friction reduction properties (hence a more responsive clutch with less slippage).  While less friction reduction properties would seem to be better for the wet clutch... it would not be best for the internal engine parts like camshaft bearings and other moving parts where friction is detrimental and would lead to premature failure.  Some folks swear you need M2 oil, while others say they have been using regular motor oil for years and their clutch is just fine.  Could they both be right ???
      Any thoughts ?
       
    • Joe Breaux
      Oil change
      By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • Tom Gorski
      2014 Cub Cadet Volunteer Oil Change
      By Tom Gorski
      Just bought a 2014 Volunteer. Can anyone tell me what parts have to come off to change the oil and filter. I can see them but I can't figure out how to access them. Thank You

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...