Quantcast
Jump to content


Rad fan question

Tinman

By Tinman
in Joyner UTV SxS Forum

 Share

Recommended Posts

Kinarfi Veteran

Kinarfi

Posted
Posted

The unit on the radiator is a switch for the indicator light on the dash, not a sensor, it is on when too hot, other wise, during normal temperatures, it is off. The one on the head, is for the ECM .

NOTE; If I remember correctly, the sensor has 2 temp sensors in it, each one referenced to ground, I could be wrong on this point, the schematic doesn't show a ground or a second output.

Link to comment
Share on other sites
  • Replies 31
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

nocturnalsixer
nocturnalsixer

How thick are the electrical wires for the fan? Stock gauge? If so u should see if the wires itself get hot, I plan on redoing my rad fan wiring with 10ga wires and the hot lead will come from altern

Tinman Community Regular

Tinman

Posted
  • Author
Posted

Hmmm. I'll have to take a closer look. When I disconnected the rad switch, my faulty temp gauge that had the needle flopping all over the place stopped working completely. My idiot light never did light at all. So I figured that this switch was for the gauge. Either my machine is wired different (possible but not probable) or then the gauge just happened to quit when I disconnected the switch.

Thanks Kinarfi.

Either way, I'll be doing what Lenny suggested - tap another hole at the head.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Lawrence
      Coolant light blinking
      By Lawrence
      Massimo coolant light blinking what does that mean?
    • Grizz
      Blowing a fuse
      By Grizz
      hello grizz again I keep blowing this fuse left side on bottom it’s a 15 amp I have checked all the wires can’t find anything bare or broken it is a 2021 axis 700 I put a 20 amp in so I could pull out of shop to take pictures. Does anyone have any suggestions. Thanks.
    • Ronald
      Check engine light on Axis Pro 70
      By Ronald
      Check engine light comes on after engine runs continuously for 5 minutes or so.  I can shut down the engine and restart and check engine light goes out, then comes back on after running 5 minutes or so?  What ya think?
    • FGT
      How to wire a C/B into a dual battery set up
      By FGT
      QUESTION: How to wire the C/B into this current dual battery set up.

      EXISTING SITUATION: MAIN Battery is OEM and feeds OEM circuits. Added an AUX Battery in the OEM dual battery location. Connected the AUX - terminal to the MAIN - terminal. Connected the 100A Accessory Fuse Block power cable to the AUX + terminal. Installed a smart isolator between AUX and MAIN batteries where a cable from AUX + goes to the isolator and a cable from isolator to MAIN battery + terminal. Installed separate QD battery tender cables to both AUX and MAIN batteries + and -. The dual battery system appears to work as intended. For this Phase 1 improvement, to avoid having to constantly pull the leads on the AUX + battery post off and put on, for testing or maintenance of Accessory circuits, I wanted a more convenient and safer way to open the circuit from the AUX battery + terminal the Accessory Fuse Block. I called an off road dealership and was told to install a much larger capacity circuit breaker than the 100A rated Fuse Block and was recommended to get a 250A C/B like the one in the pic, which I did. I was told the reason for the C/B high amp rating was two-fold (a) to trip in the event of a battery short circuit and (b) to be able to conveniently open the C/B to kill power to the Accessory Fuse Block without removing leads from the AUX + terminal. The 250A C/B has two posts labelled "BAT LOAD" and "BAT LINE". There are currently three connections to the AUX + post: (1) Accessory Fuse Block power cable, (2) cable to Isolator AUX in terminal, (3) cable from AUX battery charger.


    • Pop Bob
      Vector 500 wire connectors
      By Pop Bob
      While adjusting my suspension, I noticed an unused two wire connector on each side just hanging loose. Anyone know what they are? Nothing in the manual about them. 


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...