Quantcast
Jump to content


joyner parts in Newyork port


Recommended Posts

Buyer Beware I was the one that order these parts it went so bad that paypal gave me my money back then he sent me this email

hi,David, IF you still want to get the goods . please wire transfere the money to our account.

Please consider our request ,we still hope we can establish a long term relationship.

Link to comment
Share on other sites

Bob, Paypal gave me my money back I paid you but you could not deliver the parts I paid you what you ask I didn't charge back. I didn't get the parts paypal gave me my money back.Look everybody what he thinks about America and you want to buy parts from him.There is a storage fee over 1200.00 on these parts plus I was going to have to get them clear from customs.After 60 days paypal gave me my money back. The bill of landing didn't match up with the marking on the boxes and when I email bob all he could say is release the money and he said he's responsibity end it when he ship the parts

Link to comment
Share on other sites

Dear Mr. Plumber,

It seems that oversea re-issued a original bill of lading to the shipper. Please contact the shipper to send the original bill to us or have him surrender it at origin. Otherwise I would need it from you for collection. Please read below. thank you.

"YOUR SATISFACTION IS OUR PROMISE"

Robert Mar

Eurasia Freight Service - NYC

230-79 Int'l Airport Center Blvd Suite 250

Jamaica, NY 11413

Tel: 718-244-8887

Fax: 718-244-1682

E-Mail: [email protected]

Web Site: www.eurasiafreight.com

Link to comment
Share on other sites

hi,David,

our responsibility is over when we deliver the goods to the shipping company.

You have received the bill of loading . you have inspected the goods.

Now why you still hold the money ? If you still feel ok, get the issue resolved and release the money .

otherwise ,we will hold on the goods to wait for resolution.

Best Regards!

Bob Qiao

Link to comment
Share on other sites

Dear Mr. Plumber,

Please help AZ verify the markings on your shipment so it will transport to Louisville. On hold at AZ NY at the moment until confirmed. Tayanne and Sprite in copy. Please acknowledge, thank you.

Hbl#eurfl12512813lui. On hold for marks. Received 4 bags. Marks (70910753 deppon). Please advise, frt on hold. IT to Louisville

Rgds.

Tayanne

"YOUR SATISFACTION IS OUR PROMISE"

Robert Mar

Eurasia Freight Service - NYC

230-79 Int'l Airport Center Blvd Suite 250

Jamaica, NY 11413

Tel: 718-244-8887

Fax: 718-244-1682

E-Mail: [email protected]

Web Site: www.eurasiafreight.com

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
  • Similar Topics

    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Woody77
      UTV MASSIMOREPLACED STATOR WANT start replaced rectifier still want start stator ohms out 5 ohms each leg what could be wrong at this point 
    • By WCF
      Hi Joyner Gang
      New to the Joyner group. I'm making long travel for the 1100 Sand viper. I'm trying to make something that will work as well or even better than the RZR Rino etc. At this time the front has 14" travel rear has 16" of travel. Still developing the suspension. comets are welcome. Ask questions and I will get back to the Forum 
       
      ?
       
       

       
       

       


    • By Quentin Walker
      Hi all. I am in dire need of some help. Through our university, we are competing in the Baja SAE competition. It is a collegiate engineering design competition to design and manufacture an off road dune buddy.
      To cut to the chase, we were donated a 2011 Hisun HS 700 UTV, and we are using suspension and drivetrain parts off of it in our design. I am in the process of ordering new parts, but I am coming to a standstill.
      Does anyone have any experience ordering parts for these machine?
      From what I have found online, these machine were sold by Tractor Supply, along with a few different brands that share the same parts (Supermach, Coleman, Massimo, etc.)
      Any help is appreciated. Thanks in advance.
×
×
  • Create New...