Quantcast
Jump to content


Recommended Posts

Posted

Well, I know many 2008 & 2009 Trooper owners unknowingly became the R&D department for Joyner. I am curious to find out how the 2011 & 2012 Troopers are holding up? Have they resolved all of the common problems? What, if any, issues have you had?

My curiosity stems from wondering to recommed to my friend buying a used Trooper (cheaper but may have problems) or a new and "improved" model.

Posted

Could it be that they are holding up so well that none of the owners have had to go looking for help thus none of them on here!

rocmoc n AZ/Mexico

Posted

I haven't seen any comments anywhere on the new Troopers. Maybe none sold yet? If I were going new this would be of greater interest-

http://images.search.yahoo.com/search/images?_adv_prop=image&fr=hp-pvdt&va=renli+buggy

Casey at JMC says he will have them for sale soon. He has units currently at EPA for certification. Similar to Joyner w/Chery 1100cc and 5 sp manual trans. Available in 2wd and 4wd. Does not appear to have low range so that's a bummer. Took a ride a couple weeks ago in friends Polaris Ranger and was very impressed on severe mountain trails near Payson. It went places my Trooper would never go due to low range option. Still prefer my Joyner but this new Renli looks sweet!

Posted

Hey fellas im new here but have recently bought a 2012 trooper t2. Love the thing for sure! Only have 190 miles on it so far but it seams rock sollid really. Only chinsy thing about it are the skid plates! They are around a 16th in. Thick alluminium and for us rocky trail runners/climbers thats way to flimbsy. Almost had a rock penitrate my skid and hit my gas tank to its getting new skids built at the welders. Its an awsome rig though for sure. Not sure if the rear diff is upgraded for the 12 modle wouldnt know what to look for. Also i ordered some 29x9,50 r14 swampers for it and got lots more planned for performance wise;)

Posted

Thanks for the reply 12TrooperT2. We usually don't hear from Trooper owners until there is a problem. Good to hear you are happy with yours. Where did you buy you T2?

The stock skidplates are terrible. The screws protruding out of the bottom are even worse. I recomment a skidplate made out of UHMW.

Posted

The welder i took the skids to is building the rear diff plate out of 3/8 in. Aircraft alluminium and the mane plates out of 1/4 in. aircraft alluminium. That should do then slowly build more for the whole bottom side. You guys know if this little engine will push 29 in. tires and klimb still if its stock?

Posted

The welder i took the skids to is building the rear diff plate out of 3/8 in. Aircraft alluminium and the mane plates out of 1/4 in. aircraft alluminium. That should do then slowly build more for the whole bottom side. You guys know if this little engine will push 29 in. tires and klimb still if its stock?

I struggled with the decision to swap out my wheels and put a set of 31" on there. Did it and haven't looked back......except to smile! The extra ground clearance is awesome, and like Charlie says, 1st gear usability improved. I was worried that I would loose some of the rock crawling abilities, but I have still been able to climb all the same hills after the swap as I did before. I actually use first gear now though.

Still it should be said that the low end torque lacks the ability to impress, on an 09' model at least, regardless of the tire size.

Posted

I struggled with the decision to swap out my wheels and put a set of 31" on there. Did it and haven't looked back......except to smile! The extra ground clearance is awesome, and like Charlie says, 1st gear usability improved. I was worried that I would loose some of the rock crawling abilities, but I have still been able to climb all the same hills after the swap as I did before. I actually use first gear now though.

Still it should be said that the low end torque lacks the ability to impress, on an 09' model at least, regardless of the tire size.

What tires did you put Mariner - truck or UTV? And are you still running 14" rims?

Posted

No, 15" rims. They are the "revolver" I think is the model, made by vision. The tires are truck/jeep tires. I got them in a swap deal when rocmoc sold his T2.

They are Vision Buckshot wheels. Discount tires ordered them for me!

rocmoc n AZ/Mexico

Posted

15" rims. Crap. I just bought a 14" joyner rim for a spare. Retired and on a budget in a country with next to no choices...Guess I'll have to follow Rocmoc's math on better tire choices...

Posted

Finally got my skid plates back and going to go test em out on an elk hunt tgis weekend they only cost me $150. Also found one problem area for anyone who has a 2012 joyner to look at. Problem is that the bolts are not locktited in place and vibrate loose on the brake callipers. Allredy rattled two of my callipers untill they fell free but nothing a little BLUE LOCKTITE not red cant fix. Also if you have had this problem pay attention to the other brakes as there is a thin washer between the mounting surfaces of the calliper and the hub housing surface. Also has anyone put any interco black momba tires on their trooper? If so how ya like em?

Posted

Finally got my skid plates back and going to go test em out on an elk hunt tgis weekend they only cost me $150. Also found one problem area for anyone who has a 2012 joyner to look at. Problem is that the bolts are not locktited in place and vibrate loose on the brake callipers. Allredy rattled two of my callipers untill they fell free but nothing a little BLUE LOCKTITE not red cant fix. Also if you have had this problem pay attention to the other brakes as there is a thin washer between the mounting surfaces of the calliper and the hub housing surface. Also has anyone put any interco black momba tires on their trooper? If so how ya like em?

That little thin washer can be a pain to deal with. On mine, I tack welded it in place, making it much easier to reinstall the calipers.

Lenny.

Posted

Finally got my skid plates back and going to go test em out on an elk hunt tgis weekend they only cost me $150. Also found one problem area for anyone who has a 2012 joyner to look at. Problem is that the bolts are not locktited in place and vibrate loose on the brake callipers. Allredy rattled two of my callipers untill they fell free but nothing a little BLUE LOCKTITE not red cant fix. Also if you have had this problem pay attention to the other brakes as there is a thin washer between the mounting surfaces of the calliper and the hub housing surface. Also has anyone put any interco black momba tires on their trooper? If so how ya like em?

I went to a brembo dual caliper used on motorcycles on my front calipers. Improved the braking, but still not where I want it. I had to fab some mount brakets out of plate steel for these to work. How is the braking on the 2011/2012's? Same I would imagine...they stop you but don't really provide much feel or grab?

I run 30" dominator 540's from superatv. They have been bullet proof. I don't even worry about carrying a spare. I hit a rock in Moab and felt the tire pinch hard against the rim, the kind where you cringe and wait to hear the hiss. Upon inspection I had a small cut in the sidewall, but nothing into the threads. My friends with Maxxis Bighorns have had 4-5 holes each in their sidewalls since I have owned these. They are soft though, so if you run on the road alot I would not recommend them. When we run on the slick rock in Moab I hear other tires churp on steep inclines/declines where mine just bit & stick.

Posted

Actually the brakes on my 2012 are really good grabbing brakes. They will stop me pretty fast and most time will slide the tires on loose dirt. On asphalt i will leave skid marks easy. Gotta ask do your 30inch tires interfear with the fenders at all?

Posted

i tried 31's on my 08 and they scrubbed when turning hard if the suspension was down, now went to 30" Zilla's and am much happier. no rub no matter what you are into.

Glad you pointed that out. I forgot about that. I did have to modify the lower frame of the firewall so they wouldn't rub when cranking the wheel over.

  • 2 months later...
Posted

Hey fellas have had a couple more isues with my 2012 trooper one was a problem that evaded me for a week before i figured it out. I came down a steep grade and i mean STEEP to and the fuel pump started getting loud after i leveled out it would get quiet like it got gas now and again so luckaly we made it to camp with only a few spits and sputtrers. After getting back i noticed fuel pressure dropping off and finally syopped falling at 10 psi so i bought the pump and filter (pump out of mid 90s Ford truck & filter from a Chevy) only to find out the fule regulator set screw had came lose so watch the regulater. And the other problem is with the right front break. When aplying break it slaps like it is grabing and is lose but all looks to be good and tight anyone else have that prob? Other than that this machine is great!

T2 Trooper has 370 miles on it as of post.

  • 1 year later...
  • 2 months later...
Posted

Hi there 2Scoops! So far i have almost 1200 miles on my 12 mod year T2 and its had minor problems. Some of which i have covered. The break caliper that was slapping was due to a sticky mud plugged port which the calliper floats on. One other isue i have is the lower hiem joints on the front a arms are getting sloppy but easy fix got new ones strait from Joyner for good price think 60 dollars total. Had one shock blow a seal on the front too but this is all due to 1000 miles of rough roads so something has to give eventually i guess. Oh and the headlamp wireing was ziptied way too tight which caused a short and killed the original lamps but new set of led lamps work great. So far my setup has only changed with adding the led head lamps and 15 inch m12 diesel wheels with 29x10.50 super swamper sx bias tires. Have lots more planed tho. Hope this help with your wonders.

Posted

Yes it does. Those are very minor. Good to hear it is holding up. The guys on the Wildcat forum have all kinds of crazy problems big and small. I just bent a tie rod on my Wildcat that would have never happened on the Trooper. They used flimsy aluminum tie rods to save weight. The Trooper isn't light but it is stout.

Posted

I came down a steep grade and i mean STEEP to and the fuel pump started getting loud after i leveled out it would get quiet like it got gas now

T2 Trooper has 370 miles on it as of post.

Have you read any of the posts about how to fix the steep down hill problem, easiest is to add a surge tank. Or did they move the pump to inside the tank?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By redneckred
      Can anyone tell me how to get the engine codes to display on a 2012 Bennche Bighorn 700X?  I played with the gauges once and lucked up on this but can't remember what I did.  Will the codes automatically display if there is a code or do you have to cycle through the display?
×
×
  • Create New...