Quantcast
Jump to content


Finishing the Small Items/Problems on Project Jeep

rocmoc

By rocmoc
in All Other Off-Road Toys

 Share

Recommended Posts

rocmoc Grand Master

rocmoc

Posted
Posted

One of the problems that kept us from taking the Jeep with us was my Jeep was leaning on the left side (lower on the driver's side) after everything was mounted; New tires, new wheels, new leaf springs, new shakles & new diffs. It also caused the Jeep to dive on the driver's side when you turned quickly towards the right. I couldn't find the cause and I was under a timeline, time was running out. I was too reactionary! While traveling and upon the return home, I told myself to slow down, think and measure. I have fixed stuff like this before. So today I took the time to measure and just lay under the Jeep looking at the frame. Inch by inch comparing left side to right side. THEN, I SAW IT! The frame supporting the front spring hanger on the rear diff on the driver's side was bent. I took a floor jack and lifted the frame at the location aprox the amount of the bend and sure enough the Jeep was nearly level. In one of my shops when I poured the floor I installed tie-downs in case I ever had a problem like this. I will tie her down, jack her up until the bend is gone. I will then box both sides so this can't happen in the future. Must have happened when the right rear axle came out on the previous owner. I never saw it as the axle was hanging out when I bought her. At any rate it is a good day when you solve a problem!

rocmoc n AZ/Mexico

Link to comment
Share on other sites
  • 3 weeks later...
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

Turned out there was A LOT of small items / problems. One I have been working on is the Jeep rode and handled like cr*p. I did every easy fix there is but no improvement. Finally I took the leaf springs apart and removed 2 leafs leaving 4 in the stack. I also put a wedge in the front spring mount to improve caster. WOW what an improvement. The springs now have travel so the shocks can work. I am going to bite the bullet and purchase Fox Shocks. It seems except in the racing community, Jeep suspension technology is lagging behind. At any rate progess has been made. Second problem was / is exhaust noise. There was so much at first I could not tell the NEW Headman Headers had leaks. Finally after clearing up some of the noise I found the leaks. The surfaces of the flange is not flat & one pipe is not fully weld. I can't return them as I had to redesign one tube for clearance around the steering column. So, I have it off and doing the fixes myself. All in all I am feeling better about the new beast.

rocmoc n AZ/Mexico

Link to comment
Share on other sites
  • 2 weeks later...
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

Have been working on the handling and made BIG improvements yesterday. Added a lot more caster! She is now ready for the road. Very few rattles & small stuff left. Will continue to work on those but it is time to buy the insurance so she can be driven. Will make little local trips to post office and the such then move on to bigger trips & off road. It is getting there.

rocmoc n AZ/Mexico

Link to comment
Share on other sites
  • 2 weeks later...
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

WELL, the handling turned out the be a BIG item/issue. A Jeep requires 4+ degrees of postitve caster to drive correctly. If you have less the steering will wander making it very difficult to stay on even a smooth road. A mod I had planned for the future is reversing the shackles in the front. The spring hangers are reversed where the shackle is in the rear and the pivot / solid mount end is moved to the front. This mod ends up with A LOT of postitive caster. It worked. Completed the mod and for the first time I can drive the Jeep at speed. One more of those little items/issues and I can start enjoying. Oh yeah, two more little items/issues. Turns out I have to rebuild the transfer case, $400.

rocmoc n AZ/Mexico

Link to comment
Share on other sites
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

Ouch $400...i remember when i had to rebuild my transfer case in my 02 silverado i end up doing it myself for $400 in parts and lube, I'm more than sure you would be able to tackle a older trasfer case i just hope it's not iron

Sent from my DROID RAZR using Tapatalk 2

Good news is I still have money in the budget from the sale of my Troopers. A couple of things I don't work on is Trannys, Transfer Cases & Diffs. I will do everything else. $400 isn't that bad. I got a quote for replacing the front & rear tranny seals and the rear diff seal on a '57 Ford I own. $600 so just adding fluids & drip-pan as everthing works well, just drips.

rocmoc n AZ/Mexico

Link to comment
Share on other sites
  • 5 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Greg Kilgore
      New AXIS 550
      By Greg Kilgore
      Was at Lowe's over the weekend. The wife and I seen they have a new Axis 550. That thing is sharp. Has a complete door. Speakers in door. Bigger engine. Bench seats. New styling all the way around. Looks to be more air tight than my 2022 model. I really like the looks but $10k is out of my price range for now. Unless I could sell mine. And the resale on the Axis 500 is nothing.
      Went to the local wally world today. See a 4 person Polaris General 1000 on the back of a trailer. That Polaris looked exactly like a stretched version of the Axis 550. Even down to the vents in the windshield.
      Just wondering if anyone can confirm or deny the Axis 550 is a copy of the Polaris?
    • Duncan
      utv tires
      By Duncan
      I got a utv from lowes it has one tire in the back that is the same size as the front tires so it has 3, 26-9-14 and 1 26-11-24. i want to change the rear tire to the same one as the other.So instead of buying a new rim will a 26-11-24 tire fit on a 26-9-14 rim.
    • Isaac
      My side by side is not runing right I think it’s in limp mode
      By Isaac
      I have a 2013 odes dominator when I get in it.  It ideals fine but when you give it gas it bogs and goes and bogs and won’t go passed 30 can anyone help me 
    • hdtran
      Do you wear a helmet when riding your side-by-side UTV?
      By hdtran
      That's the question! Or, if you want to add details:
      (a) How do you use the UTV? (roads? off-road to get to trees? etc.)
      (b) If you are wearing a helmet--how frequently? What type of helmet?
       
      My own answers: (a) Most of the time off-road to get to downed trees, cut the trees to logs and haul the logs back for splitting. (b) Very rarely, a ski helmet and not a motorcycle helmet.
    • Mike Turner
      American SportWorks LM650 starting problems.
      By Mike Turner
      American SportWorks LM 650 won’t start at times. Starter won’t engage the solenoid just “clicks” much like a weak battery would cause. Battery was replaced and problem went away and then came back. Replaced positive battery terminal. Problem resolved then returned. Replaced negative battery terminal. Problem gone then returned. Replaced the positive and negative battery cable ends. Problem resolved and now returned. The repair lasts for maybe 12 starts, then the solenoid just “clicks” again as it will with a weak battery. So I replaced the ignition switch. Problem solved for a week. With each “fix” the problem is resolved but only temporarily. Does anyone have any suggestions ? To replace the starter is expensive especially if it’s not the problem. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...