Quantcast
Jump to content


silverbullet response


Recommended Posts

The DB gauge is the one I went with and it works well. No issues at all except hooking it up can be a pain in the ass. Need to really look at the wires you are hooking up and where they go or don't go as the instructions suck and the customer service at Innovate out here in Irvine, CA sucks even worse. Guy is an a-hole at Innovate to say the least and he is their customer service. I ended up talking to the tech guy at Dobeck as they are very familiar with the Innovate air/fuel gauges and how they are set up. To get the Fuel programmer dialed in correctly I actually called the tech guy at Dobeck while out riding and dialed it in. Might have to adjust fuel pressure some and will have to play with the fuel controller some but he will walk you through it. You won't get 11HP but I did notice some increase and oddly enough sound difference as well once it was dialed in. Fuel economy will suffer as it does use the fuel. Without a gauge you just don't know what you are running and thus you almost have to go with a fuel/air gauge to make sure you are set.

Link to comment
Share on other sites

Hey SB, Looks like your thread got hi-jacked again. Talking about someone else's product.....Maybe if you actually responded these would be your customers talking about your product. Instead since you still have not made any attempt to contact me and wont respond, I'll chime in here and let everyone know...

http://www.amazon.co...uel+ratio+gauge

Same A/F gauge SB sells, ships immediately, reputable seller, guaranteed to actually get your part, and its CHEAPER.

WOW I can't believe this is not taken care of yet. I will not buy anything else from Jose no more until he takes care of this I ask all the people on here to help this man and not buy anything from Jose.This could be you next and you would want everybody to help you too.Lets send a message to Jose that this is WRONG. JOYNER USA will now get my business.
Link to comment
Share on other sites

WOW I can't believe this is not taken care of yet. I will not buy anything else from Jose no more until he takes care of this I ask all the people on here to help this man and not buy anything from Jose.This could be you next and you would want everybody to help you too.Lets send a message to Jose that this is WRONG. JOYNER USA will know get my business.

they got mine.i got my knew bearings thanks joyner usa. dedub
Link to comment
Share on other sites

WOW I can't believe this is not taken care of yet. I will not buy anything else from Jose no more until he takes care of this I ask all the people on here to help this man and not buy anything from Jose.This could be you next and you would want everybody to help you too.Lets send a message to Jose that this is WRONG. JOYNER USA will know get my business.

Agreed,

There's lot i want like the bush guard and headlight combo and other stuff i could probably drop 4-5k at sb but i refuse to buy anything more from sb until sb resolve the issue with merchant marnier

simple as that..... principles and customer service come first

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites

i just received my fuel controller and A/F gauge from SB this afternoon, under 15 days just as Jose promised. not sure what to make of all the SB bashing but i am a happy customer. i will say that although i am a happy customer, i wont be placing any more orders with SB until merchant mariner is looked after.

again, thanks for the parts Jose, i hope to install and be tire spinning by tomorrow afternoon.

Link to comment
Share on other sites

The DB gauge is the one I went with and it works well. No issues at all except hooking it up can be a pain in the ass. Need to really look at the wires you are hooking up and where they go or don't go as the instructions suck and the customer service at Innovate out here in Irvine, CA sucks even worse. Guy is an a-hole at Innovate to say the least and he is their customer service. I ended up talking to the tech guy at Dobeck as they are very familiar with the Innovate air/fuel gauges and how they are set up. To get the Fuel programmer dialed in correctly I actually called the tech guy at Dobeck while out riding and dialed it in. Might have to adjust fuel pressure some and will have to play with the fuel controller some but he will walk you through it. You won't get 11HP but I did notice some increase and oddly enough sound difference as well once it was dialed in. Fuel economy will suffer as it does use the fuel. Without a gauge you just don't know what you are running and thus you almost have to go with a fuel/air gauge to make sure you are set.

Wat kind of advice did the Dobeck tech give you on dialing in the fuel controller? Maybe he gave you some tips that could help me dial mine in a little better!

Link to comment
Share on other sites

Hey guys I have the fuel controller from sb I have had it for a whole now. I spoke with the tech department st ejk I believe it is the company that actually made the controller. I asked what should the set up be he told me if your running a snorkel and factory exhaust wich a lot of us are that to leave the programmer at the factory setting. He said with a wide band ad sensor precat converter and the post o2 disconnected you want 13.5 area at idle and low speeds 12.8 when you getting on it he said that will be best power for those mods and safest fuel economy will suffer lol. Just figured this would help also they recommended aem or innovations for the wide band af sensor

Link to comment
Share on other sites

Hey guys I have the fuel controller from sb I have had it for a whole now. I spoke with the tech department st ejk I believe it is the company that actually made the controller. I asked what should the set up be he told me if your running a snorkel and factory exhaust wich a lot of us are that to leave the programmer at the factory setting. He said with a wide band ad sensor precat converter and the post o2 disconnected you want 13.5 area at idle and low speeds 12.8 when you getting on it he said that will be best power for those mods and safest fuel economy will suffer lol. Just figured this would help also they recommended aem or innovations for the wide band af sensor

Hey Charlie,

Do your fuel controller have any vacuum Ports on controller itself?

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites

No vacuum ports at all on the fuel controller. Best thing to do is call Dobeck Performance who makes the fuel controllers and they can help you dial it in. You may have to change your fuel pressure as well as I had to. If fuel pressure is too high then it affects the fuel controller. I had to turn down my fuel pressure to get the fuel controller to be able to do its job. If you call Dobeck just tell them you purchased a fuel controller through Silver Bullet and they will help you with it.

Link to comment
Share on other sites

nocturnalsixer

no vacume ports on my controller, yours does????

Charlie

Nope no fuel controller here yet I'm just asking because i heard about those..

No vacuum ports at all on the fuel controller. Best thing to do is call Dobeck Performance who makes the fuel controllers and they can help you dial it in. You may have to change your fuel pressure as well as I had to. If fuel pressure is too high then it affects the fuel controller. I had to turn down my fuel pressure to get the fuel controller to be able to do its job. If you call Dobeck just tell them you purchased a fuel controller through Silver Bullet and they will help you with it.

Bruhaw

I tried to get one through a member on forum but he didn't answer so i plan on calling dobeck myself and ask themabout that because i want a controller than can sense the turbo positive boost and negative vacuum like An secondary manifold absolute pressure sensor but for fuel controller

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites

Charlie

Nope no fuel controller here yet I'm just asking because i heard about those..

Bruhaw

I tried to get one through a member on forum but he didn't answer so i plan on calling dobeck myself and ask themabout that because i want a controller than can sense the turbo positive boost and negative vacuum like An secondary manifold absolute pressure sensor but for fuel controller

Sent from my DROID RAZR using Tapatalk 2

i have one of them i'm sending to goindeep. doebec has ben makeing for.me. dedub
Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Eagle Mountain Outfitters
      Our R&D team just finished the first unit and wanted to show you guys. Need more cargo space without losing the functionality of being able to fold down the seat to use the full bed? Eagle Mountain Outfitters, the maker of the original metal UTV roof, has designed a foldable rear cargo basket to meet your needs. Price is $625 + $30 shipping.  If you have any question's, please reach out to me at [email protected]
       

    • By Poppateets
      I just purchased a used 2023 Massimo warrior UTV SxS 1000mx with 600 miles on it. I didn't even get a full day of riding and the driver's side rear axle broke. I'm pretty sure it was already going bad because we would hear a noise once in a while. I'm wondering if anyone else has had problems with theirs. Also looking for places to buy accessories.
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • By joynersfuntillitbreaks
      so i just picked up a 2008 1100 trooper and iv ordered a few parts for it now and 99% of what i got fits perfect my issue now is my rear wheel hub is stripped out got a new cv and it fits great but i order 2 different hubs from 2 different places now and they are both wrong the spline opening is to small to fit the factory cv shaft and yes the shaft factory part #s are the same paid 250 for an original new replacement if anyone has anything that works to replace the original hub please point me in the right direction 
×
×
  • Create New...