Quantcast
Jump to content


Best UTV for work


Rod

Recommended Posts

Hi everybody! I’m new here and I wish to request for your help and advice. I hope to find dispassionate opinions.

I need to buy a UTV only for work. My priorities are reliability and torque. I need to climb (and descend) clayish very steep slopes, one with a small sliding rock surface (maybe 4 feet diameter, where rains “washed” clay) at a narrow point of the trail, so one side wheels have to ride on the rock. This trail is just at cliff edge at this point. A tractor struggled hard with this place recently to climb because wheel sliding on rock surface.

Big Red has engine brake that would be good for my need. I do not need a great cargo capacity, but it will be appreciated from time to time. I’m concerned about plastic bed strength. Honda does not inform about power or torque. Basic model has no roof or windshield.

What is new on 2013 Big Red in regard to 2011 model? I may get a good price on a 2011 apparently new one (clearance).

Otherwise, Club Car XRT 1550 seems good too. It has hard plastic roof, windshield, power steering, tilt steering, and 2 years warranty (Honda only 1). Does it still have carburetor? It seems out-of-date.

Kioti Mechron seems to be rock solid and has other advantages, but dealer is an issue (far from my place and bad service).

Kubota RTV 900 also seems to be rock solid but is much more expensive.

Rhino 700 has engine braking, but no roof or windshield, and less cargo capacity (only 400 lb).

Gator XUV 825 is 20 % more expensive than Big Red, without power steering, tilt steering, roof and windshield, and only has 1 year warranty.

Polaris seems to have several good items but less reliability.

So, I’m expecting your opinions. Thanks!

Link to comment
Share on other sites

I have been more than happy with my Joyner trooper and it has 5 speed manual and rear and also front diff that locks up for extra traction.

For cargo i has built a payload box like a pick up have for my trooper it worked very good for my needs also

Python is 2wd and renegade have smaller engine so id probably suggest trooper the most..

http://www.joyner-atv-utv.com/

Also trooper use a 4 cylinder efi engine and 5 speed manual transmission where all other companies so far use v twin engines and cvt (if belt get wet it slip...an disadvantage) also if you are more interested in trooper. Feel free to message me or go to Joyner section of the utvboard forum

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner
    • By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • By shawn b
      my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated
×
×
  • Create New...