Quantcast
Jump to content


Recommended Posts

Posted

Hey guys got a question. I am looking at getting a toy hauler camper to haul the 4-wheelers and joyner. I have a 2011 Eco-boost F-150 and the problem is the only camper large enough to put the trooper in is too expensive and probably close to the limits of my truck. So what I was thinking is get the smaller one which is 21 feet long and put a tow bar on the trooper to tow behind the camper. Has anyone flat towed a trooper? I plan on going with 15inch all terrain automotive tires. Is this a bad idea? I know I see people towing campers with boats behind them all the time so I didnt think it would be a problem. Would it be better to buy a small utility trailer to put behind the camper? Any suggestions would be appreciated. Oh yeah thanks for all the responses in my other threads. I am in afghanistan and dont get to visit the site a whole lot.

Posted

Well I ran into the same exact thing. Toy haulers are way wxpensive......SO what I am maybe going to do is buy a 28 foot Enclosed car hauler and make my own..6000 for a new car hauler...Give or take for the brand and emenitys. I figure if I get a used one for 3000 and put 2000 in it I will have about what I want..Some states you are Not allowed to doulble tow....Just depends .I posted a link on my facebook.I will try to find it and post it here....

Posted

IMHO, the ring & pinion are too small dia for continuous use at high speed (and my GUESS would be above 40 mph) and both front & rear diffs will be turning. Older Jeeps had/have the same problem with small dia wheels & tires used with low diff gear ratios, burns up the bearings. My off-road Jeep has 4:88 gears with 33" tires and will be trailered. My Jeep pulled behind the Motorhome has 3:73 gears with 30" tires and I still don't/won't pull over 60 mph. I am sure someone else will jump in. Better to get a flat trailer for the Trooper and double pull like Lenny does. Oh by the way, still have my trailer used for the Trooper. It is for sale but will be listing it this week with the sandrail on the local Craigslist. I would sale it without the sandrail. Sidenote for friends who have been out with us when we used the sandrail, Forgot the better 3/4 gets motion sickness when I bought it and that is was happened within minutes of first time out. If I can't take my best buddy, then the sandrail goes.

rocmoc n AZ/Mexico

Posted

check with the state laws. when you double tag trailers the first trailer is supposed to be a 5th wheel or goose neck... when we came and picked the two we bought from you we were not legal...

  • 2 weeks later...
Posted

I really like the carrier that fits on the truck bed, but i wonder if that would be too much with a 1700 pound joyner and the tongue weight of a camper on a half ton truck?

Posted

Too much weight. That would max out a 3/4 ton and maybe then some. Keep in mind that every 1000 pounds on the hitch ball is going to transfer about 300 pounds from the front axel to the rear. I wouild be suprised if the tongue weight on your camperr is only 1000 pounds, Probably more like 1600-1700 pounds bear minimum. Based on the weight distribution of the Trooper, pretty much all of its 1700 pounds will be on the rear axel. Then between the driver and passenger, only front seat considered, if they total 300 pounds, that puts another about 75 pounds on the rear axel. To round things out, that would be (1600 x 1.3) + 1700 + 75 = 3855 pounds, too much even for a 3/4 ton. you would need a 1 ton truck. You can recalculate using the actual weight of the camper tongue. but you really need to get down to nor more then maybe 2200 - 2300 pounds. I would pull a trailer behind the camper if your around stated that allow that. Even then the camper would need to be a 5th wheel. Your only real answer is to trade your camper in on a toy hauler.

Lenny

PS: forgot to add the weight of the carrier frame, probably another 200 pounds on the rear, at least.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Texjpr
      2002 ranger 500 4x4 stopped running and wouldn't restart. Service manual wiring diagram helped identify the hub safety switch as the culprit. Using jumper wires to bypass  switch allowed the engine to start and run normally. Inspection of switch showed melted epoxy and a strong smell of burnt electrical. Unable to find replacement part either used or new. Is there a work around other than jumper wiring?
    • By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • By joynersfuntillitbreaks
      so i just picked up a 2008 1100 trooper and iv ordered a few parts for it now and 99% of what i got fits perfect my issue now is my rear wheel hub is stripped out got a new cv and it fits great but i order 2 different hubs from 2 different places now and they are both wrong the spline opening is to small to fit the factory cv shaft and yes the shaft factory part #s are the same paid 250 for an original new replacement if anyone has anything that works to replace the original hub please point me in the right direction 
    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
×
×
  • Create New...