Quantcast
Jump to content
This Topic


Help disconnecting locker cable

Nickb1907

By Nickb1907
in Joyner UTV SxS Forum

 Share

Recommended Posts

Nickb1907 Rookie

Nickb1907

Posted
Posted

I tried searching for this and looking through the manual before I posted. I can't seem to figure out how to disconnect the cable from the pin coming out of the differential. I need to disconnect it to install the U shaped bracket that bolts to the diff that the cable goes through for the locker. My rear didnt have anything there.

BTW i modeled up and did a drawing on the bracket based off the the front. If yall have a bracket that everyone could use, I can model it up, do a drawing and anyone could take it to a local welding shop and have it made. See attached bracket.

post-1749-0-01388700-1358878730_thumb.png

Guest Lenny

Guest Lenny

Posted
Posted

If you look closely, you will see a slot on the side of the pin. Youhave to rotate the cable to the side to line the cable u p with the slot and it will slide out. Its a bit of a pain to put back on with the bracket. What cad program are you using? I used to use autocad but for the last several years have used Solidworks.

Lenny

Nickb1907 Rookie

Nickb1907

Posted
  • Author
Posted
  On 1/22/2013 at 7:32 PM, Lenny said:
If you look closely, you will see a slot on the side of the pin. Youhave to rotate the cable to the side to line the cable u p with the slot and it will slide out. Its a bit of a pain to put back on with the bracket. What cad program are you using? I used to use autocad but for the last several years have used Solidworks.

Lenny

Solidworks, but i have used all the others. We build frac equipment at work so i have access to all the fab stuff.

Guest Lenny

Guest Lenny

Posted
Posted

It looked like the Solidworks background color. Great software once you learn it. Not much it can't do.

Lenny

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • Steve Waldner
      Looking for a Kioti Mechron 2200
      By Steve Waldner
      Looking to buy a Kioti Mechron 2200
    • strike250
      Free Massimo Buck 400 service manual
      By strike250
      I have the factory service manual available for the Buck 400. Just send me a message with your email and I'll get it to you. Although there is no charge for this, it would be great if  you would visit my website where you could donate any amount to help do things like this with others who need it. Again, there is no charge for this manual, and no obligation to donate. But if you did, I would thank you for sure. Have fun on the trails. www.warriorsoffroad.com
       
      Matt

    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind
    • Jim Kessell
      Predator 670 manual oil pressure gauge
      By Jim Kessell
      Hi All
      Just installed a predator 670 on my Landmaster. My question is can I remove the low oil pressure wire fitting and plumb my mechanical gauge into that access point?
      Thanks in advance for your advice !!
      Jim

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...